The new Maxiva UAXT/VAXT Multi-Compact family of UHF & VHF solid-state Transmitters, Transposers (Translators) and on-channel Gap Fillers expands upon the proven foundation of GatesAir low-power systems and PowerSmart® high-efficiency technology.Today’s broadcasters and network operators are continually searching for more efficient and economical approaches for providing reliable over-the-air transmission. When several DTV channels can be consolidated into one common transmission site, the cost and space requirements for individual equipment per channel can often be very significant. The innovative Multi-Compact architecture allows the possibility of many configurations, with up to 8 independent low power transmitters, transposers or gap fillers, to be configured into a single space-saving chassis. The Maxiva Multi-Compact provides pre-filter power levels up to 15W per module, in a compact and convenient 4RU 19” rack mount package.
Designed for digital or analog broadcasting, the Maxiva Multi-Compact is a platform available in Transmitter, Transposer or SFN Gap Filler configurations for DVB-T/H, DVB-T2, ATSC, ATSC-MDTV, ISDB-Tb and analog networks. The Maxiva Multi-Compact can be configured for up to 8 independent systems, or as N+1, N+2 or N+1/M+1 configurations.Instead of investing into several separate transmitter units, as well as complex and costly redundancy management systems, broadcasters or network operators can now simply invest into a single 4RU Multi-Compact transmitter and operate up to 7 channels with +1 redundancy in a single compact unit.
Main Features of Maxiva™ UAXT Multi-Compact / VAXT Multi-CompactMaxiva Multi-Compact Platform:
- Up to 15 Watts average power per module
- High efficiency broadband amplifier technology
- Extremely compact 4RU 19” rack mount chassis
- Single chassis configurable for up to 7+1, or 6+2 redundancy configurations
- Several Input interfaces for each transmitter module:
- 1 x ASI input (TS, BTS, T2MI, SMPTE-310M)
- 1 x GbE input (TS over IP)
- Optional: 1 x DVB-S/S2 Satellite Receiver input per slot (including CAM interface and multi-stream capabilities)
- Optional: 1 x RF receiver input for repeater/gap-filler configuration
- DVB-T/H/T2, ISDB-T/Tb, DAB/DAB+/T-DMB, ATSC and analog modulations fully supported
- Embedded ASI and RF Matrix for redundancy management of each transmitter module
- Embedded Re-Multiplexer/Layer Combiner/TS to BTS (188 to 204 byte) converter for ISDB-Tb
- Adaptive pre-correction circuits
- 2 x hot swappable high stability GPS / GLONASS receivers with battery
- 2 x hot swappable power supplies
- SNMP, Web Interface and Touch Screen display
UAXT / VAXT Multi-Compact – Primary Components
- Multi-Compact Chassis, 4RU, with 8 slots, to be fitted with plug-in transmitters/transposer/gap filler modules for N+1 or N+2 configurations. Includes 1 power supply, 1 GPS / GLONASS receiver and RF output matrix.
- 15 W UHF Digital TV transmitter plug-in module., with 1x ASI, 1x GbE inputs and ASI matrix (up to 8 per chassis)
- 15 W UHF Digital TV transposer/gap-filler plug-in with echo cancellation
Standard Options & Accessories
- Redundant power supply option (Hot-swappable unit)
- Redundant GPS / GLONASS receiver option (Plug-in board)
- 26 dB LNA GPS / GLONASS antenna. includes mounting kit and 25 meters coaxial cable
- DVB-S/S2 integrated receiver board per slot, single and multi-stream, with CAM slot
- RF integrated receiver board for transposer/gap-filler operation
- DVB-S/S2 integrated input matrix for N+1 or N+2 configuration
- RF integrated input matrix for N+1 or N+2 configuration
- Software option for ISDB-Tb Remux/Layer combiner/ TS to BTS (188 to 204 byte) converter
- Dual-cast software option, adds DVB-T modulation
- Dual-cast software option, adds DVB-T2 modulation
- Dual-cast software option, adds ISDB-T modulation
- Dual-cast software option, adds ATSC modulation
Other products from this company:
FLEXIVA™ COMPACT
FLEXIVA™ HIGH POWER
INTRAPLEX® ASCENT
INTRAPLEX® IPCONNECT
Maxiva ULX-OP / VLX-OP
MAXIVA™ IMTX-70
MAXIVA™ PMTX-1
MAXIVA™ STREAMASSURE
MAXIVA™ UAXT MULTI-COMPACT / VAXT MULTI-COMPACT
Maxiva™ UAXT Ultra-Compact / VAXT Ultra-Compact
MAXIVA™ VAXTE
MAXIVA™ XTE
FLEXIVA™ COMPACT
Flexiva is designed for low- and high-power requirements, up to 80 kW, while utilizing the most compact design on the market today. Flexiva continues the legacy of the highly successful line of GatesAir FM transmitters and combines innovative, new quadmode RF amplification and software-defined exciter technology to take FM transmission to the next level.
Featuring PowerSmart® technology, the Flexiva line offers unmatched efficiency that makes it ideal for all FM applications. The 50-volt LDMOS device technology delivers a dramatic increase in power density, lower operating costs and reduced cost of ownership over the life of the transmitter.
As the digital transmission leader, GatesAir has developed a solid core competency backed by years of experience in the complex technical areas that are essential for maximum transmitter performance.
Customers can count on GatesAir for implementation. The company offers a range of support options from standard 24/7 telephone technical assistance and parts to installation, training, full system design and field maintenance contracts.
Main Features of Flexiva™ Compact
Power levels up to 3850 W Analog FM, 3100 W FM+HD
Broadband, frequency agile design 87.5 to 108 MHz requires no tuning or adjustments
Best-in-class power efficiency for lowest operating costs
Compact, space-saving, 2, 3 or 4RU design
State-of-the-art, direct-to-carrier digital modulator
Integrated stereo encoder
ITU-R BS412 peak program/multiplex power limiter
Static RDS generator
2 AES, 1 analog L/R and 2 composite program inputs with automatic failover switching
Digital MPX/Composite input over AES192 interface with fail-over switching
Operation over a wide range of voltage and power stability conditions
Operation at up to 1.5:1 VSWR with proportional foldback
Full remote control capability including:
Web-based HTML GUI interface
SNMP
Parallel control/monitoring
Extensive Fault, Warning and Operational parameter logging
N+1, dual transmitter and main/alternate; automatic switching capability
Optional Features
GPS receiver for SFN synchronization
Orban Optimod™ 5500H multi-band audio processor
Gen 4 HD Radio™ Exgine modulator card
';
FLEXIVA™ FLX
Flexiva FLX utilizes the latest 50 volt LDMOS amplifier devices, compact high-efficiency power supplies, variable speed cooling and the Flexiva FAX exciter with RTAC™.
Featuring PowerSmart® 3D technology, the Flexiva FLX line offers unmatched efficiency that makes it ideal for all FM applications. FLX provides today’s broadcaster with unparalleled power efficiency and outstanding signal performance.
This powerful blend of new technologies provides best-in-class performance with respect to transmitter power efficiency, physical size, performance and features. The modular design allows for simpler installation, infrequent maintenance requirements together with dramatically reduced total cost of ownership over the life of the transmitter.
Main Features of Flexiva™ FLX with PowerSmart® 3D
Featuring 4th Generation HD Radio Crest Factor Reduction and Adaptive Pre-Correction technology for the highest HD Radio™ power available.
Flexiva High Power Transmitter features identical power blocks for scalability. 10,000 Watts to 80,000 Watts
Small and compact. 10kW power blocks in 16 rack units
Variable speed coolant pumps and heat exchanger cooling fans maximize system efficiency
Common dual power amplifiers and IPA modules for all power levels simplifies spares
Single-phase or 3 phase power, Delta or Wye configurations. 190 to 464 VAC
1:1 Power supply to Power Amplifier module maximizes redundancy
Hot-Pluggable, hot-swappable power amplifier and power supply modules minimizes down-time and simplifies maintenance.
Simple, distributed hardware based control architecture uses analog circuits to control critical transmitter functions. Not reliant on a microprocessor for high reliability
Hardware based life support backup controller provides added robustness, reliability
Can use any standard FM exciter or can be tightly integrated with FAX low power exciter
Fully broadband, 87.5 to 108MHz — requires no tuning or adjustments.
Best-in-class power efficiency — lowest operating costs
Extremely high power density; compact and lightweight space-saving design
Latest state-of-the-art LDMOS-FET power amplifier technology, high efficiency (98%) auto ranging, hot-pluggable power supplies
Maintain power up to 1.5:1 VSWR with proportional VSWR fold-back above that for safe operation at reduced power into marginal loads (icy antenna etc.)
Automatic restart after AC mains interruption; returns to previous operational mode
Global control and monitoring via the World Wide Web remote graphic user interface (GUI) works with any PC, table or smart phone
Full SNMP network control and monitoring support
In-depth diagnostics and setup via an easy-to-use front panel control
Dual-drive with automatic failover exciter switching
FLX 10K Available Options
Internal or External pump system
';
FLEXIVA™ HIGH POWER
Flexiva is designed for low- and high-power requirements, up to 80 kW, while utilizing the most compact design on the market today. Flexiva continues the legacy of the highly successful line of GatesAir FM transmitters and combines innovative, new quad-mode RF amplification and software-defined exciter technology to take FM transmission to the next level.
Featuring PowerSmart® technology, the Flexiva line offers unmatched efficiency that makes it ideal for all FM applications. The 50-volt LDMOS device technology delivers a dramatic increase in power density, lower operating costs and reduced cost of ownership over the life of the transmitter.
As the digital transmission leader, GatesAir has developed a solid core competency backed by years of experience in the complex technical areas that are essential for maximum transmitter performance. Customers can also count on GatesAir for implementation, and the company offers a range of support options from standard 24/7 telephone technical assistance and parts to installations, training, full system design and field maintenance contracts.
The Flexiva™ air-cooled FM solid-state transmitter family provides today’s broadcaster with a single transmission platform capable of analog and digital operation. Incorporating field-proven GatesAir technology, Flexiva transmitters deliver world-class performance, reliability and quality.
Flexiva is designed for low- and high-power requirements, up to 80 kW, while utilizing the most compact design on the market today. Flexiva continues the legacy of the highly successful line of GatesAir FM transmitters and combines innovative, new quad-mode RF amplification and software-defined exciter technology to take FM transmission to the next level.
Featuring PowerSmart® technology, the Flexiva line offers unmatched efficiency that makes it ideal for all FM applications. The 50-volt LDMOS device technology delivers a dramatic increase in power density, lower operating costs and reduced cost of ownership over the life of the transmitter.
As the digital transmission leader, GatesAir has developed a solid core competency backed by years of experience in the complex technical areas that are essential for maximum transmitter performance. Customers can also count on GatesAir for implementation, and the company offers a range of support options from standard 24/7 telephone technical assistance and parts to installations, training, full system design and field maintenance contracts.
';
FLEXIVA™ LX
Flexiva LX is ideal for low power requirements, up to 1 kW, while utilizing the most compact design on the market today. Flexiva continues the legacy of the highly successful line of GatesAir FM transmitters and combines innovative RF amplification and software-defined exciter technology including powerful integrated multi-band audio processing to make your station stand out on a budget.
Featuring PowerSmart® technology, the Flexiva LX continues the legacy of unmatched efficiency that makes it ideal for all FM applications. The 50-volt LDMOS device technology delivers a dramatic increase in power density, lowers operating costs and reduced cost of ownership over the life of the transmitter.
Customers can count on GatesAir for implementation. The company offers a range of support options from standard 24/7 telephone technical assistance and parts to installation, training, full system design and field maintenance contracts.
Flexiva LX FM Transmitter Family Features:
Power levels up to 1050 W
Broadband, frequency agile design
87.5 to 108 MHz requires no tuning or adjustments
Hot-pluggable power supplies
Best-in-class power efficiency for lowest operating costs
Compact, space-saving, 2RU design
State-of-the-art, direct-to-carrier digital modulator
Integrated digital multi-band audio processor and stereo encoder with composite clipper
ITU-R BS412 peak program/multiplex power limiter
Dynamic RDS generator
AES, analog L/R and 2 configurable composite program inputs and outputs
Digital MPX/Composite input over AES192
Operation over a wide range of voltage and power stability conditions
Operation at up to 1.5:1 VSWR with proportional fold back
Full remote control capability including:
Web-based HTML GUI interface SNMP
RS-232
Parallel control/monitoring
Extensive Fault, Warning, and Operational parameter logging
Optional Powerful DSP based re-broadcast receiver
';
INTRAPLEX® ASCENT
The scalability of Ascent makes it ideal for applications that require multiple channels of audio encoding and decoding at head-end sites. The high-density solution reduces cost and provides a path for convergence of IT and broadcast infrastructure. The interoperability between Ascent and IP Link codecs provides a complementary solution for remote contribution and distribution use cases.
Product Details
The Ascent platform continues the Intraplex tradition of providing an unprecedented level of reliability for audio over IP application. Built with enhanced network reliability and security in mind, Ascent supports the Dynamic Stream Splicing technology of IP Link codec, which provides “hitless” protection for packet losses using the combination of time and network diversity for packet transmission, and FEC.
To further enhance reliability and security, the platform supports the SRT protocol encapsulation. SRT (Secure Reliable Transport) is an open-source protocol that provides low-latency, reliable and secure streaming of audio and video data. The reliability in SRT is accomplished by a built-in packet re-transmission scheme; the security of streams is handled by the built-in AES-128/256 payload encryption.
In addition to “hitless” protection, like the IP Link codecs, the Ascent also supports automatic failover between different incoming streams or stored audio.
This combination of capabilities gives Intraplex codecs a market-leading position in STL over IP technology and unmatched network transport reliability.
Ascent supports both physical audio interfaces (AES3, Analog) and AES67 (AoIP), with a maximum of 16 full-duplex or a total of 32 channels (combination of encode and decode). Physical audio interfaces can be ordered as 4- or 8-channel cards, supporting both AES3 and analog audio signals. The Ascent product is built on the Commercial-Off-The-Shelf (COTS) x86 architecture to leverage the scalability and cost of the technology. The product is available in a 1RU branded hardware server and as a software-only option.
Main Features of Intraplex® Ascent
- 4, 8, 16 stereo channels. Each channel can be full-duplex, encode-only or decode-only
- Supports AES3, Analog and AES67 audio input and outputs
- Standard Coding: Linear, Opus
- Optional: AAC-HE, AAC-HEv2, AAC- ELD, AAC-xHE, MPEG 2 and MPEG 3 audio coding
- Protocol Encapsulation: Real-time Transport Protocol (RTP), Secure Reliable Transport (SRT)
- Streams: Multicast, unicast, and multi-unicast
- 10 streams per channel with up to 20 destinations per transmit stream; maximum of 100 streams per system
- Three independent IP interfaces for redundant network operation
- Built-in silence sensor with optional stream switchover
- Automatic backup to audio playout from USB drive or external audio source
- Multicoding: can encode the same audio source in multiple formats
- Prioritized stream sources at the output with automatic switch over and switch back between primary and secondary streams and backup sources (streams, USB, external audio source)
- Programmable RTP level Forward Error Correction (FEC) scheme
- Programmable time diversity and Interleaving of streams to combat burst packet losses
- Integrated scheduler for automated scheduled program switching
- Integrated with Intraplex LiveLook (network analytics and monitoring software)
- Web and SNMP for management
- Multiple web account types to restrict access
- GPIOs: up to 32 in, 8 out. Available for stream transport and alarm assignment
- Network reliability
- Dynamic Stream Splicing with network and time diversity for “hitless” packet loss protection
- Programmable RTP level Forward Error Correction (FEC)
- Secure Reliable Transport (SRT): new protocol provides automatic packet retransmission method
- IP Security
- Access control per interface
- Encryption of streams with AES-128
';
INTRAPLEX® HD LINK™
Our challenge: to design a studio-to-transmitter link (STL) for your most demanding 950 MHz applications — one as reliable and robust as Intraplex® T1 and IP audio links. Digital STL manages much more than audio, so installation and configuration need to be straightforward, not a science project. Data should not be optional, requiring additional boxes and complexity. Your STL should be ready, out of the box, for AM, FM and HD Radio™, as well as future multimedia applications.
Earlier digital STLs were not designed for IP data transport. Adding IP data to them required optional modules and external add-ons, and many engineers working on HD Radio installations reported spending much time and money trying to eliminate glitches.
Our solution: HD Link™ is designed to manage all HD Radio™ transport scenarios, regardless of where you place your importer and exporter. Its two prioritized Ethernet paths give preference to HD Radio™ data over control and other LAN/WAN data. It supports both UDP and TCP, and even handles the switching of TCP return packets over asymmetric IP paths with plug-and-play simplicity.
HD Link offers RF power to spare, an integrated IP gateway with sophisticated data handling capabilities, and multiple channels of audio. The intuitive front panel and remote interfaces tap into the most complete feature set of any microwave STL, yet take less time to configure. It can even operate on both RF and IP simultaneously, and allows automatic backup of all services from one to the other.
Intraplex is broadcasting’s first choice for rock-solid, full-time operation of T1 STLs. With HD Link, you can now count on the same dependable performance, superior support and long-term value for your microwave links.
';
INTRAPLEX® IP LINK
By incorporating three IP Interfaces that can be used for streaming and management, the IP Link systems can provide a level of reliability not seen in comparably-priced codecs.
As the latest additions to the Intraplex line of data transport products, the IP Link family of audio codecs bring legendary Intraplex reliability to the IP codec market.
IP Link 100/100p: Single bidirectional stereo audio channel IP Link 200: Two bidirectional stereo audio channels IP Link 200A: Two bidirectional stereo audio channels with one channel being AES67 Standard: Linear, AAC-LC, Opus and G.722 audio coding Optional: AAC-HE, AAC-HEv2, AACELD, MPEG2, MPEG3 and Enhanced aptX audio coding Optional: Automatic audio loudness leveling and metering compliant with EBU R-128 and ITU-R Optional: IPConnect capability to reliably transport external IP packets Other transport modes: Transparent AES up to 192 kbps to support composite FM multiplex signal over AES Protocol Encapsulation: RTP, SHOUTcast/Icecast, MPEG-TS Three independent IP interfaces for redundant network operation Optional redundant power supply: 12VDC or 48VDC Built-in silence sensor with optional stream switch over Automatic backup to audio playout from USB drive or external audio source Multicoding can encode the same audio source in multiple formats for STL, backup, and web streaming Optional Dynamic Stream Splicing providing “hitless” operation and T1/ E1 circuit like performance on less predictable IP networks Prioritized stream sources at the output with automatic switch over and switch back between primary and secondary streams and backup sources (streams, USB, external audio source) Programmable RTP level Forward Error Correction (FEC) scheme Programmable time diversity and interleaving of streams to combat burst packet losses Integrated with Intraplex IP Link Scheduler for automated scheduled program switching Integrated with Intraplex LiveLook (network analytics and monitoring software) N+1 redundancy with integrated control of external switching equipment IP Link 200/200A/100p: SynchroCast™ option provides dynamically managed precision delay for Single Frequency Network (SFN) broadcasting and simulcasting Support for IP multicast and multi-unicast Web browser user interface and SNMP network management Eight multipurpose contact closure inputs and outputs provide: Transport of logic signals with time-alignment to audio Stream control Alarm notification
';
INTRAPLEX® IPCONNECT
IPConnect solves the problem of reliable transport across complex networks that traditionally suffer data loss through dropped packets. IPConnect provides an added layer of reliability for many types of IP traffic such as HD Radio, DAB/DAB+, or DRM by employing a combination of packet protection schemes with network/time diversity and packet-level forward error correction. Additionally, IPConnect can bridge local area network (LAN) segments across wide-area networks with seamless tunneling to enhance reliability of program and signal transport across large geographical regions with multiple receiving and transmitting sites.
With its three network interfaces, IPConnect’s data gateway provides extra protection through packet encapsulation, which encloses external IP data packets in a GatesAir protocol wrapper as it moves across IP networks. IPConnect provides this protection for studio-generated data, as well as IP data from external sources. While the former might include RDS data or SNMP control signals to trigger a command at the transmitter site, the latter may incorporate program or control data coming from a network operations center, satellite feed or advertising service.
As the next-generation member in GatesAir Intraplex family of IP codecs, the award-winning IPConnect leverages the strengths of previous IP Link codecs—including GatesAir’s patented Dynamic Stream Splicing (DSS) technology to mitigate IP packet loss, eliminate off-air time, and optimize stream reliability.
';
INTRAPLEX® LIVELOOK
Intraplex LiveLook provides both a real-time analytics as well as a monitoring and notification platform for the IP Link audio codec systems. The analytics capability of LiveLook uses Burst Packet Loss modeling technique to analyze the patterns of packet losses, which is then used by the internal decision tree to provide recommendation on the most effective packet loss mitigation technique of the IP Link to apply.
The monitoring capability can simultaneously collect long-term statistics on multiple audio streams, which can be used for historical analysis. The notification capability creates a separate alarm log for each audio stream and can optionally send email notification to the user on the state of the audio stream.
';
Maxiva ULX-OP / VLX-OP
The Maxiva OP Series transmitter system comprises several sub-parts:
- An exciter (dual drive is optional), with Real-Time Adaptive Pre-correction, and multiple input interface options (ASI, T2MI, ETI, EDI, IP, Satellite) and an optional onboard GPS / GLONASS receiver for accurate synchronization and SFN timing;
- One or more Power Amplifier modules (Stand-alone single PA systems and from 2 to 8 per rack depending on model and the output power level);
- A control and monitoring unit, with embedded change-over system;
- An innovative, high-efficiency air-cooling or liquid-cooling system.
Maxiva OP Series transmitters support several digital modulation standards (DVB-T, DVB-T2, ISDB-T/Tb, DAB/DAB+, ATSC, and PAL/NTSC Analogue standards. Dualcast systems are also available.
Maxiva OP Series transmitters incorporate innovative World-class engineering, providing unparalleled AC-to-RF efficiency, performance, ease-of-use, and low maintenance costs.
Main Features of Maxiva™ OP Series
- Compact design: Lower power systems are stand-alone 2+1 RU or 3+1 RU 19” rack-mount. Larger systems include one or more 36RU or 42RU equipment racks.
- A wide range of output power levels and configurations are available suiting all needs worldwide
- Doherty high-efficiency wideband or broadband amplifier technology, available in UHF, VHF Band III, and VHF Band I
- Built-in ASI/RF matrix for automatic exciter switch-over, without the need of using an external switchover unit
- DVB-T, DVB-T2, ISDB-T/Tb, DAB/DAB+, ATSC, NTSC, and PAL (with NICAM) modulations are fully supported
- Embedded Re-Multiplexer/Layer Combiner/TS to BTS (188 to 204 byte) converter for ISDB-Tb
- Real-Time Adaptive Pre-correction
- Optional onboard high stability GPS / GLONASS receiver with battery
- Flexible input interfaces available:
- 4 x ASI inputs (TS, BTS, T2MI, SMPTE-310M) + Analog input
- 2 x ASI inputs and 2 x Gigabit Ethernet
- 4 x ETI or 2 x ETI + 2 x EDI inputs
- 3 x ETI inputs
- 1 x DVB-S/S2 Satellite Receiver input
- 1 x RF input
';
MAXIVA™ IMTX-70
The diminutive dimensions of the Maxiva IMTX-70 chassis are key to this unique design. Measuring only 230 x 485 x 320 mm, it allows installation into a wide variety structures. Access is via a lockable and sealed door. Cooling air is provided by vertical air convection within the mast structure, complemented by small fans inside the chassis.
Although extremely compact in size, the Maxiva IMTX-70 boasts many features normally found in full-size systems, including the capability of housing up to six separate transmitter modules, each with up to 70W of average DTV power. Each module can be configured as a transmitter, translator, or on-channel gap-filler with echo-cancellation, using optional input cards. A DVB-S/S2 satellite receiver option is also available as well as GbE (TS over IP), ASI, T2MI, SMPTE-310M, and ETI inputs. Digital modulations are supported include; ATSC, DVB-T, DVB-T2, and ISDB-T. For ISDB-T/Tb applications, an embedded Re-Multiplexer and Layer Combiner/TS to BTS, can be included.
The RF output stage is a high-efficiency Doherty broadband amplifier for energy savings and minimal waste heat. For added redundancy the Maxiva IMTX includes dual redundant power supplies, configurable as 2 x DC, 2 x AC or 1 AC plus 1 DC. Remote control includes SNMP and a Web interface.
Main Features of Maxiva™ IMTX-70
- Compact chassis: 230 x 485 x 320 mm
- Up to 6 separate transmitter modules
- Output power: Up to 70W rms per module
- Input interface options for each module:
- ASI, BTS, T2MI, SMPTE-310M, ETI
- Gbe port (TS over IP)
- DVB-S/S2 Satellite Receiver input (including CAM interface)
- RF receiver input for transposer/gap-filler configuration
- Supports DVB-T/H, ISDB-T/Tb, DVB-T2, DAB/DAB+, ATSC modulations
- Embedded Re-Multiplexer/Layer Combiner/TS to BTS (188 to 204 byte) converter for ISDB-Tb
- Adaptive pre-correction circuits
- High stability GPS / GLONASS receivers with battery
- Option for 2 x hot swappable power supplies, 2 AC or 2 DC and/or AC/DC
- SNMP, Web Interface and Touch Screen display
- RF combiner option for multiple transmitter systems
';
MAXIVA™ PMTX-1
The compact dimensions (351W x 224D x 460H mm) of the Maxiva PMTX-1 chassis are key to this unique design, allowing installation on a wide variety of outdoor poles, or mast structures. Access is via a lockable and sealed door. The sealed metal housing of the PM-TX-1has been engineered to remove heat efficiently from the internal circuitry. The unique design of the PMTX-1 provides a high level of installation versatility, allowing it to be installed on virtually any suitable outdoor structure.
This versatile unit does not require a building, shelter or any additional outdoor enclosure. The totally sealed metal case has been designed specifically for outdoor environmental conditions, providing protection from all humidity levels, precipitation and wide temperature extremes.
The unit can be configured and operated as a 50W digital / 100W analogue transmitter, transposer or an on-channel gap-filler, with various input options. A satellite receiver card with CAM slot is also available. The unit includes an internal mask filter. The external power source requirement is 36-72 VDC (positive or negative).
Main Features of Maxiva™ PMTX-1
- Compact chassis: 351W x 224D x 460H mm
- Outdoor, pole-mounted, using adapter plate
- Output Power (Post-Filter): 50W rms Digital or 100W analogue
- Input interface options:
- ASI, BTS, T2MI, SMPTE-310M, ETI
- Gbe port (TS over IP)
- DVB-S/S2 Satellite Receiver input (including CAM interface). 4 slots available.
- RF receiver input for Transposer/Gap-Filler configuration (Direct Conversion – zero IF)
- Regenerative receiver input option for Transposer
- Supports DVB-T/H, ISDB-T/Tb, DVB-T2, ATSC & Analogue modulations
- Embedded Re-Multiplexer/Layer Combiner/TS to BTS (188 to 204 byte) converter for ISDB-Tb
- Adaptive pre-correction circuits
- Optional High stability GPS / GLONASS receiver with battery
- SNMP, Web Interface and Touch Screen display
- RF combiner option for multiple transmitter systems
';
MAXIVA™ STREAMASSURE
Rapid isolation of performance issues across signal transport and RF infrastructure is another key value proposition for broadcasters. The ability to separately analyze multiple IP, ASI and other streams ahead of the transmitter versus the RF and decoded audio/video streams coming out allows users to quickly identify and address the source of the problem
The StreamAssure system is fully scalable from a single transmitter deployment to a large-scale network, comprising a vast number of sites deployed over a wide geography.
Options are available from an simple and economic monitoring solution to a comprehensive end-to-end system, including compliance recording and streaming.
';
MAXIVA™ UAXT MULTI-COMPACT / VAXT MULTI-COMPACT
The new Maxiva UAXT/VAXT Multi-Compact family of UHF & VHF solid-state Transmitters, Transposers (Translators) and on-channel Gap Fillers expands upon the proven foundation of GatesAir low-power systems and PowerSmart® high-efficiency technology.Today’s broadcasters and network operators are continually searching for more efficient and economical approaches for providing reliable over-the-air transmission. When several DTV channels can be consolidated into one common transmission site, the cost and space requirements for individual equipment per channel can often be very significant. The innovative Multi-Compact architecture allows the possibility of many configurations, with up to 8 independent low power transmitters, transposers or gap fillers, to be configured into a single space-saving chassis. The Maxiva Multi-Compact provides pre-filter power levels up to 15W per module, in a compact and convenient 4RU 19” rack mount package.
Designed for digital or analog broadcasting, the Maxiva Multi-Compact is a platform available in Transmitter, Transposer or SFN Gap Filler configurations for DVB-T/H, DVB-T2, ATSC, ATSC-MDTV, ISDB-Tb and analog networks. The Maxiva Multi-Compact can be configured for up to 8 independent systems, or as N+1, N+2 or N+1/M+1 configurations.Instead of investing into several separate transmitter units, as well as complex and costly redundancy management systems, broadcasters or network operators can now simply invest into a single 4RU Multi-Compact transmitter and operate up to 7 channels with +1 redundancy in a single compact unit.
Main Features of Maxiva™ UAXT Multi-Compact / VAXT Multi-CompactMaxiva Multi-Compact Platform:
- Up to 15 Watts average power per module
- High efficiency broadband amplifier technology
- Extremely compact 4RU 19” rack mount chassis
- Single chassis configurable for up to 7+1, or 6+2 redundancy configurations
- Several Input interfaces for each transmitter module:
- 1 x ASI input (TS, BTS, T2MI, SMPTE-310M)
- 1 x GbE input (TS over IP)
- Optional: 1 x DVB-S/S2 Satellite Receiver input per slot (including CAM interface and multi-stream capabilities)
- Optional: 1 x RF receiver input for repeater/gap-filler configuration
- DVB-T/H/T2, ISDB-T/Tb, DAB/DAB+/T-DMB, ATSC and analog modulations fully supported
- Embedded ASI and RF Matrix for redundancy management of each transmitter module
- Embedded Re-Multiplexer/Layer Combiner/TS to BTS (188 to 204 byte) converter for ISDB-Tb
- Adaptive pre-correction circuits
- 2 x hot swappable high stability GPS / GLONASS receivers with battery
- 2 x hot swappable power supplies
- SNMP, Web Interface and Touch Screen display
UAXT / VAXT Multi-Compact – Primary Components
- Multi-Compact Chassis, 4RU, with 8 slots, to be fitted with plug-in transmitters/transposer/gap filler modules for N+1 or N+2 configurations. Includes 1 power supply, 1 GPS / GLONASS receiver and RF output matrix.
- 15 W UHF Digital TV transmitter plug-in module., with 1x ASI, 1x GbE inputs and ASI matrix (up to 8 per chassis)
- 15 W UHF Digital TV transposer/gap-filler plug-in with echo cancellation
Standard Options & Accessories
- Redundant power supply option (Hot-swappable unit)
- Redundant GPS / GLONASS receiver option (Plug-in board)
- 26 dB LNA GPS / GLONASS antenna. includes mounting kit and 25 meters coaxial cable
- DVB-S/S2 integrated receiver board per slot, single and multi-stream, with CAM slot
- RF integrated receiver board for transposer/gap-filler operation
- DVB-S/S2 integrated input matrix for N+1 or N+2 configuration
- RF integrated input matrix for N+1 or N+2 configuration
- Software option for ISDB-Tb Remux/Layer combiner/ TS to BTS (188 to 204 byte) converter
- Dual-cast software option, adds DVB-T modulation
- Dual-cast software option, adds DVB-T2 modulation
- Dual-cast software option, adds ISDB-T modulation
- Dual-cast software option, adds ATSC modulation
';
Maxiva™ UAXT Ultra-Compact / VAXT Ultra-Compact
The new Maxiva UAXT & VAXT Ultra-Compact family of UHF solid-state Transmitters / Transposers (Translators) and on-channel Gap Fillers expands upon the proven foundation of GatesAir low-power systems and PowerSmart® high-efficiency technology. It provides today's digital broadcaster with a suite of compatible products to accommodate any coverage application, along with unmatched performance, reliability and quality.
The Maxiva Ultra-Compact family further extends the capabilities of the Maxiva series, providing a single family of transmission products capable of satisfying any coverage architecture. The Maxiva Ultra-Compact provides pre-filter power levels up to 1,000W, in exceptionally compact and space-saving 1RU, 2RU and 3RU packages.
Designed for both analogue and digital broadcasting, the Maxiva UAXT/VAXT Ultra-Compact is a platform available in Transmitter, Transposer or SFN Gap Filler configurations for DVB-T, DVB-T2, ATSC, ISDB-Tb, DAB/DAB+ and NTSC/PAL analogue networks. The Maxiva Ultra-Compact Series provides an ideal solution for extending market coverage and filling in coverage gaps in challenging situations, including busy urban areas that require greater building penetration.
The Maxiva UAXT & VAXT Ultra Compact family of Transposers and on-channel Gap Fillers provide efficient and reliable re-broadcast of the received signal in a space saving, reliable and robust package. The Gap Filler configuration adds a powerful echo cancellation feature to deliver exceptional on-channel performance. For ATSC (8-VSB) Gap Filler applications, a new on-channel Spectrum Restorer utilizing EDOCR technology provides unsurpassed performance. This combination of products enables broadcasters to address any network coverage requirement.
Maxiva Ultra-Compact Platform:
- High-efficiency broadband amplifier technology
- Power levels up to 1,000W (pre-filter average power)
- Frequency agile broadband design (two bands):
- UHF Band IV/V, 470 to 810 MHz
- VHF Band III, 170-240 MHz
- Extremely compact, space-saving, 1RU, 2RU, and 3RU 19” chassis
- Full local/remote control capability including:
- Local touch-screen display
- Web GUI interface
- SNMP
Transposer / Translator:
- Supports analog and digital standards
- Direct baseband conversion (zero IF) and fully regenerative conversion options available
SFN Gap Filler:
- Includes a powerful echo cancellation circuit, 15dB of Gain Margin
- Low processing delay, < 10 µS
- Cancellation window width 20 µS
- Selective cancellation window range 1.6 µS to 820 µs
- MER degradation < 2dB
- ATSC SFN Gap Filler is now realizable using GatesAir's (8-VSB) Spectrum Restorer
';
MAXIVA™ UAXTE
Optimized for International Markets
The Maxiva UAXTE utilizes the latest generation 50 volt LDMOS amplifier devices, new compact high-efficiency power supplies and the Maxiva Compact series exciter/driver along with real-time adaptive correction (RTAC) for outstanding signal performance. The Maxiva UAXTE power amplifiers have been optimized to provide the best possible performance and efficiency for both ATSC 1.0 and ATSC 3.0. The UAXTE transmitter is rate for identical average power levels for both modulations, assuring a simple and cost-effective upgrade path for future ATSC 3.0 operation. The modular design further simplifies installation and reduces maintenance costs, dramatically lowering the total cost of ownership over the transmitters life-cycle.
The Maxiva UAXTE with PowerSmart Plus is an efficiency-optimized UHF transmitter. This all-new design includes several energy saving features.
Up to 44% AC-to-RF efficiency
Simple and cost-effective upgrade path from ATSC 1.0 to ATSC 3.0 at the same power level.
Efficiency-optimized – for highest efficiency and lowest cost of ownership
Variable speed fans to intelligently save energy
Hot-swappable, compact, high-efficiency DC power supplies
Hot-swappable, compact, high-efficiency power amplifiers
Incorporates the XTE-based Maxiva Compact exciter/driver for best-in-class performance
RoHS compliant / CE compliant
Support for all worldwide digital modulation standards
Modular & upgradeable architecture
All-digital linear and nonlinear pre-correction: Real-Time Adaptive Correction (RTAC)
Rugged, reliable design and construction
Ideal for N+1 configurations since all transmitters are identical and use the same PA’s, minimizing spares requirements
Lowest energy usage
Minimum operating cost
';
MAXIVA™ ULXTE
Optimized for International Markets The Maxiva ULXTE transmitter utilizes the latest 50-Volt LDMOS amplifier devices, new compact high-efficiency power supplies and the new Maxiva XTE exciter with advanced real-time adaptive correction (RTAC) for outstanding signal performance.
The Maxiva ULXTE power amplifiers have been optimized to provide the best possible performance and efficiency for both ATSC 1.0 and ATSC 3.0. The ULXTE transmitter is rated for identical average power levels for both modulations, assuring a simple and cost-effective upgrade path for future ATSC 3.0 operation.
Modular designs simplify installation and reduce ongoing maintenance, dramatically lowering total cost of ownership over the life of the transmitter.
Main Features of Maxiva™ ULXTE with PowerSmart® Plus The Maxiva ULXTE with PowerSmart® Plus is the highest efficiency broadband UHF transmitter on the market.
Up to 45% AC-to-RF efficiency Simple and cost-effective upgrade path from ATSC 1.0 to ATSC 3.0 at the same power level New high-efficiency DC power supplies Integrated high-efficiency pump system for certain power classes Hot-swappable light-weight PA modules Hot-swappable compact DC power supplies Incorporates the newest technology Maxiva XTE exciter for best-in-class adaptive pre-correction and native IP transport inputs RoHS compliant / CE compliant Support for all worldwide digital modulation standards Modular & upgradeable architecture All-digital linear and nonlinear pre-correction: Real-Time Adaptive Correction (RTAC) Rugged, reliable design and construction Ideal for N+1 configurations since all transmitters can be identical and use the same PA’s, minimizing spares requirements Lowest energy usage Minimum operating cost
';
MAXIVA™ VAXTE
Optimized for International Markets
The Maxiva VAXTE utilizes the latest generation 50 volt LDMOS amplifier devices, new compact high-efficiency power supplies and the Maxiva Compact series exciter/driver along with real-time adaptive correction (RTAC) for outstanding signal performance. The Maxiva VAXTE power amplifiers have been optimized to provide the best possible performance and efficiency for all modulations. For example, the VAXTE transmitter is rated for identical average power levels for 8-VSB and OFDM TV modulations, assuring a simple and cost-effective upgrade path for future ATSC 3.0 operation. The modular design further simplifies installation and reduces maintenance costs, dramatically lowering the total cost of ownership over the transmitters life-cycle.
The Maxiva VAXTE with PowerSmart Plus is an efficiency-optimized VHF transmitter. This all-new design includes several energy saving features.
Simple and cost-effective upgrade path from ATSC 1.0 to ATSC 3.0 at the same power level
Includes TSoIP / Native IP Transport inputs for ATSC 3.0 and DAB EDI interfaces
Efficiency-optimized – for highest efficiency and lowest cost of ownership
Variable speed fans to intelligently save energy
Hot-swappable, compact, high-efficiency DC power supplies
Hot-swappable, compact, high-efficiency power amplifiers
Incorporates the XTE-based Maxiva Compact exciter/driver for best-in-class performance
RoHS compliant / CE compliant
Support for all worldwide digital modulation standards
Modular & upgradeable architecture
All-digital linear and nonlinear pre-correction: Real-Time Adaptive Correction (RTAC)
Rugged, reliable design and construction
Broadband high-efficiency PA’s support redundancy and N+1 applications
Lowest energy usage
Minimum operating cost
';
MAXIVA™ XTE
Featuring unparalleled signal processing power, a smaller footprint and advanced Transport Stream over IP (TSoIP) input capabilities, Maxiva XTE builds upon a strong legacy of groundbreaking technological advances, pioneered by several decades of GatesAir innovations. Dramatically increased processing power together with new, advanced Real-Time Adaptive Correction (RTAC) techniques, provides optimum signal performance over a wide variety of modulations and RF amplifier topologies.
The Maxiva XTE supports a full range of digital broadcast standards, including ATSC, DVB-T/H, DVB-T2, ISDB-T, DTMB, DAB/DAB+/DMB. It is upgradeable to future new modulations, including ATSC 3.0, as they become available.
Main Features of Maxiva™ XTE
Advanced Real Time Adaptive Correction (RTAC)
Optimized correction for all amplifier types
Frequency Agile – Band I, III, IV and V
Supports all widely used TV standards and DAB/DAB+ radio
Upgradeable to emerging digital standards
Available Internal GNSS (GPS/GLONASS) receiver for precision frequency control and/or timing required for SFN
Available Internal UPS
Compact 1RU design
Dual redundant TSoIP inputs with seamless auto-switching
Dual redundant transport stream inputs with seamless auto-switching for ASI/T2MI
Integrated ISDB-Tb Remux
Seamless integration with GatesAir transmitters
Intuitive Web GUI interface with HTML
Advanced monitoring and diagnostics support
';
Related Products:
Maxiva™ UAXT Ultra-Compact / VAXT Ultra-Compact
DTV-H20 Series
DTU-H10 Series
DTV-M20 Series
DTU-M10 Series
MAXIVA™ UAXT MULTI-COMPACT / VAXT MULTI-COMPACT
Maxiva ULX-OP / VLX-OP
MAXIVA™ PMTX-1
MAXIVA™ IMTX-70
MAXIVA™ VAXTE
MAXIVA™ XTE
Master Control & Playout Services
Medium power VHF tansmitters
TV Transposers
TLWH7900 Series
Anywave
R&S®BSCC 5G broadcast service and control...
R&S®THU9evo
R&S®TLU9 Transmitter and GapFiller Family
Maxiva™ UAXT Ultra-Compact / VAXT Ultra-Compact
The new Maxiva UAXT & VAXT Ultra-Compact family of UHF solid-state Transmitters / Transposers (Translators) and on-channel Gap Fillers expands upon the proven foundation of GatesAir low-power systems and PowerSmart® high-efficiency technology. It provides today's digital broadcaster with a suite of compatible products to accommodate any coverage application, along with unmatched performance, reliability and quality.
The Maxiva Ultra-Compact family further extends the capabilities of the Maxiva series, providing a single family of transmission products capable of satisfying any coverage architecture. The Maxiva Ultra-Compact provides pre-filter power levels up to 1,000W, in exceptionally compact and space-saving 1RU, 2RU and 3RU packages.
Designed for both analogue and digital broadcasting, the Maxiva UAXT/VAXT Ultra-Compact is a platform available in Transmitter, Transposer or SFN Gap Filler configurations for DVB-T, DVB-T2, ATSC, ISDB-Tb, DAB/DAB+ and NTSC/PAL analogue networks. The Maxiva Ultra-Compact Series provides an ideal solution for extending market coverage and filling in coverage gaps in challenging situations, including busy urban areas that require greater building penetration.
The Maxiva UAXT & VAXT Ultra Compact family of Transposers and on-channel Gap Fillers provide efficient and reliable re-broadcast of the received signal in a space saving, reliable and robust package. The Gap Filler configuration adds a powerful echo cancellation feature to deliver exceptional on-channel performance. For ATSC (8-VSB) Gap Filler applications, a new on-channel Spectrum Restorer utilizing EDOCR technology provides unsurpassed performance. This combination of products enables broadcasters to address any network coverage requirement.
Maxiva Ultra-Compact Platform:
- High-efficiency broadband amplifier technology
- Power levels up to 1,000W (pre-filter average power)
- Frequency agile broadband design (two bands):
- UHF Band IV/V, 470 to 810 MHz
- VHF Band III, 170-240 MHz
- Extremely compact, space-saving, 1RU, 2RU, and 3RU 19” chassis
- Full local/remote control capability including:
- Local touch-screen display
- Web GUI interface
- SNMP
Transposer / Translator:
- Supports analog and digital standards
- Direct baseband conversion (zero IF) and fully regenerative conversion options available
SFN Gap Filler:
- Includes a powerful echo cancellation circuit, 15dB of Gain Margin
- Low processing delay, < 10 µS
- Cancellation window width 20 µS
- Selective cancellation window range 1.6 µS to 820 µs
- MER degradation < 2dB
- ATSC SFN Gap Filler is now realizable using GatesAir's (8-VSB) Spectrum Restorer
';
DTV-H20 Series
- Top level Energy Efficiency - User friendly interface and easy maintenance - Liquid-cooled system - Applicable for DVB-T, DVB-T2 and ISDB/T/Tb
DTU-H10 Series
- Top level Energy Efficiency - User friendly interface and easy maintenance - Liquid-cooled system - Applicable for DVB-T, DVB-T2 and ISDB/T/Tb
DTV-M20 Series
DTU-M10 Series
DTU-L10 Series
- Compact, all-in-one design- Wideband Doherty Technology- User friendly interface and easy maintenance- Air-cooled system - Applicable for DVB-T, DVB-T2 and ISDB/T/Tb
MAXIVA™ UAXT MULTI-COMPACT / VAXT MULTI-COMPACT
The new Maxiva UAXT/VAXT Multi-Compact family of UHF & VHF solid-state Transmitters, Transposers (Translators) and on-channel Gap Fillers expands upon the proven foundation of GatesAir low-power systems and PowerSmart® high-efficiency technology.Today’s broadcasters and network operators are continually searching for more efficient and economical approaches for providing reliable over-the-air transmission. When several DTV channels can be consolidated into one common transmission site, the cost and space requirements for individual equipment per channel can often be very significant. The innovative Multi-Compact architecture allows the possibility of many configurations, with up to 8 independent low power transmitters, transposers or gap fillers, to be configured into a single space-saving chassis. The Maxiva Multi-Compact provides pre-filter power levels up to 15W per module, in a compact and convenient 4RU 19” rack mount package.
Designed for digital or analog broadcasting, the Maxiva Multi-Compact is a platform available in Transmitter, Transposer or SFN Gap Filler configurations for DVB-T/H, DVB-T2, ATSC, ATSC-MDTV, ISDB-Tb and analog networks. The Maxiva Multi-Compact can be configured for up to 8 independent systems, or as N+1, N+2 or N+1/M+1 configurations.Instead of investing into several separate transmitter units, as well as complex and costly redundancy management systems, broadcasters or network operators can now simply invest into a single 4RU Multi-Compact transmitter and operate up to 7 channels with +1 redundancy in a single compact unit.
Main Features of Maxiva™ UAXT Multi-Compact / VAXT Multi-CompactMaxiva Multi-Compact Platform:
- Up to 15 Watts average power per module
- High efficiency broadband amplifier technology
- Extremely compact 4RU 19” rack mount chassis
- Single chassis configurable for up to 7+1, or 6+2 redundancy configurations
- Several Input interfaces for each transmitter module:
- 1 x ASI input (TS, BTS, T2MI, SMPTE-310M)
- 1 x GbE input (TS over IP)
- Optional: 1 x DVB-S/S2 Satellite Receiver input per slot (including CAM interface and multi-stream capabilities)
- Optional: 1 x RF receiver input for repeater/gap-filler configuration
- DVB-T/H/T2, ISDB-T/Tb, DAB/DAB+/T-DMB, ATSC and analog modulations fully supported
- Embedded ASI and RF Matrix for redundancy management of each transmitter module
- Embedded Re-Multiplexer/Layer Combiner/TS to BTS (188 to 204 byte) converter for ISDB-Tb
- Adaptive pre-correction circuits
- 2 x hot swappable high stability GPS / GLONASS receivers with battery
- 2 x hot swappable power supplies
- SNMP, Web Interface and Touch Screen display
UAXT / VAXT Multi-Compact – Primary Components
- Multi-Compact Chassis, 4RU, with 8 slots, to be fitted with plug-in transmitters/transposer/gap filler modules for N+1 or N+2 configurations. Includes 1 power supply, 1 GPS / GLONASS receiver and RF output matrix.
- 15 W UHF Digital TV transmitter plug-in module., with 1x ASI, 1x GbE inputs and ASI matrix (up to 8 per chassis)
- 15 W UHF Digital TV transposer/gap-filler plug-in with echo cancellation
Standard Options & Accessories
- Redundant power supply option (Hot-swappable unit)
- Redundant GPS / GLONASS receiver option (Plug-in board)
- 26 dB LNA GPS / GLONASS antenna. includes mounting kit and 25 meters coaxial cable
- DVB-S/S2 integrated receiver board per slot, single and multi-stream, with CAM slot
- RF integrated receiver board for transposer/gap-filler operation
- DVB-S/S2 integrated input matrix for N+1 or N+2 configuration
- RF integrated input matrix for N+1 or N+2 configuration
- Software option for ISDB-Tb Remux/Layer combiner/ TS to BTS (188 to 204 byte) converter
- Dual-cast software option, adds DVB-T modulation
- Dual-cast software option, adds DVB-T2 modulation
- Dual-cast software option, adds ISDB-T modulation
- Dual-cast software option, adds ATSC modulation
';
Maxiva ULX-OP / VLX-OP
The Maxiva OP Series transmitter system comprises several sub-parts:
- An exciter (dual drive is optional), with Real-Time Adaptive Pre-correction, and multiple input interface options (ASI, T2MI, ETI, EDI, IP, Satellite) and an optional onboard GPS / GLONASS receiver for accurate synchronization and SFN timing;
- One or more Power Amplifier modules (Stand-alone single PA systems and from 2 to 8 per rack depending on model and the output power level);
- A control and monitoring unit, with embedded change-over system;
- An innovative, high-efficiency air-cooling or liquid-cooling system.
Maxiva OP Series transmitters support several digital modulation standards (DVB-T, DVB-T2, ISDB-T/Tb, DAB/DAB+, ATSC, and PAL/NTSC Analogue standards. Dualcast systems are also available.
Maxiva OP Series transmitters incorporate innovative World-class engineering, providing unparalleled AC-to-RF efficiency, performance, ease-of-use, and low maintenance costs.
Main Features of Maxiva™ OP Series
- Compact design: Lower power systems are stand-alone 2+1 RU or 3+1 RU 19” rack-mount. Larger systems include one or more 36RU or 42RU equipment racks.
- A wide range of output power levels and configurations are available suiting all needs worldwide
- Doherty high-efficiency wideband or broadband amplifier technology, available in UHF, VHF Band III, and VHF Band I
- Built-in ASI/RF matrix for automatic exciter switch-over, without the need of using an external switchover unit
- DVB-T, DVB-T2, ISDB-T/Tb, DAB/DAB+, ATSC, NTSC, and PAL (with NICAM) modulations are fully supported
- Embedded Re-Multiplexer/Layer Combiner/TS to BTS (188 to 204 byte) converter for ISDB-Tb
- Real-Time Adaptive Pre-correction
- Optional onboard high stability GPS / GLONASS receiver with battery
- Flexible input interfaces available:
- 4 x ASI inputs (TS, BTS, T2MI, SMPTE-310M) + Analog input
- 2 x ASI inputs and 2 x Gigabit Ethernet
- 4 x ETI or 2 x ETI + 2 x EDI inputs
- 3 x ETI inputs
- 1 x DVB-S/S2 Satellite Receiver input
- 1 x RF input
';
MAXIVA™ PMTX-1
The compact dimensions (351W x 224D x 460H mm) of the Maxiva PMTX-1 chassis are key to this unique design, allowing installation on a wide variety of outdoor poles, or mast structures. Access is via a lockable and sealed door. The sealed metal housing of the PM-TX-1has been engineered to remove heat efficiently from the internal circuitry. The unique design of the PMTX-1 provides a high level of installation versatility, allowing it to be installed on virtually any suitable outdoor structure.
This versatile unit does not require a building, shelter or any additional outdoor enclosure. The totally sealed metal case has been designed specifically for outdoor environmental conditions, providing protection from all humidity levels, precipitation and wide temperature extremes.
The unit can be configured and operated as a 50W digital / 100W analogue transmitter, transposer or an on-channel gap-filler, with various input options. A satellite receiver card with CAM slot is also available. The unit includes an internal mask filter. The external power source requirement is 36-72 VDC (positive or negative).
Main Features of Maxiva™ PMTX-1
- Compact chassis: 351W x 224D x 460H mm
- Outdoor, pole-mounted, using adapter plate
- Output Power (Post-Filter): 50W rms Digital or 100W analogue
- Input interface options:
- ASI, BTS, T2MI, SMPTE-310M, ETI
- Gbe port (TS over IP)
- DVB-S/S2 Satellite Receiver input (including CAM interface). 4 slots available.
- RF receiver input for Transposer/Gap-Filler configuration (Direct Conversion – zero IF)
- Regenerative receiver input option for Transposer
- Supports DVB-T/H, ISDB-T/Tb, DVB-T2, ATSC & Analogue modulations
- Embedded Re-Multiplexer/Layer Combiner/TS to BTS (188 to 204 byte) converter for ISDB-Tb
- Adaptive pre-correction circuits
- Optional High stability GPS / GLONASS receiver with battery
- SNMP, Web Interface and Touch Screen display
- RF combiner option for multiple transmitter systems
';
MAXIVA™ IMTX-70
The diminutive dimensions of the Maxiva IMTX-70 chassis are key to this unique design. Measuring only 230 x 485 x 320 mm, it allows installation into a wide variety structures. Access is via a lockable and sealed door. Cooling air is provided by vertical air convection within the mast structure, complemented by small fans inside the chassis.
Although extremely compact in size, the Maxiva IMTX-70 boasts many features normally found in full-size systems, including the capability of housing up to six separate transmitter modules, each with up to 70W of average DTV power. Each module can be configured as a transmitter, translator, or on-channel gap-filler with echo-cancellation, using optional input cards. A DVB-S/S2 satellite receiver option is also available as well as GbE (TS over IP), ASI, T2MI, SMPTE-310M, and ETI inputs. Digital modulations are supported include; ATSC, DVB-T, DVB-T2, and ISDB-T. For ISDB-T/Tb applications, an embedded Re-Multiplexer and Layer Combiner/TS to BTS, can be included.
The RF output stage is a high-efficiency Doherty broadband amplifier for energy savings and minimal waste heat. For added redundancy the Maxiva IMTX includes dual redundant power supplies, configurable as 2 x DC, 2 x AC or 1 AC plus 1 DC. Remote control includes SNMP and a Web interface.
Main Features of Maxiva™ IMTX-70
- Compact chassis: 230 x 485 x 320 mm
- Up to 6 separate transmitter modules
- Output power: Up to 70W rms per module
- Input interface options for each module:
- ASI, BTS, T2MI, SMPTE-310M, ETI
- Gbe port (TS over IP)
- DVB-S/S2 Satellite Receiver input (including CAM interface)
- RF receiver input for transposer/gap-filler configuration
- Supports DVB-T/H, ISDB-T/Tb, DVB-T2, DAB/DAB+, ATSC modulations
- Embedded Re-Multiplexer/Layer Combiner/TS to BTS (188 to 204 byte) converter for ISDB-Tb
- Adaptive pre-correction circuits
- High stability GPS / GLONASS receivers with battery
- Option for 2 x hot swappable power supplies, 2 AC or 2 DC and/or AC/DC
- SNMP, Web Interface and Touch Screen display
- RF combiner option for multiple transmitter systems
';
MAXIVA™ VAXTE
Optimized for International Markets
The Maxiva VAXTE utilizes the latest generation 50 volt LDMOS amplifier devices, new compact high-efficiency power supplies and the Maxiva Compact series exciter/driver along with real-time adaptive correction (RTAC) for outstanding signal performance. The Maxiva VAXTE power amplifiers have been optimized to provide the best possible performance and efficiency for all modulations. For example, the VAXTE transmitter is rated for identical average power levels for 8-VSB and OFDM TV modulations, assuring a simple and cost-effective upgrade path for future ATSC 3.0 operation. The modular design further simplifies installation and reduces maintenance costs, dramatically lowering the total cost of ownership over the transmitters life-cycle.
The Maxiva VAXTE with PowerSmart Plus is an efficiency-optimized VHF transmitter. This all-new design includes several energy saving features.
Simple and cost-effective upgrade path from ATSC 1.0 to ATSC 3.0 at the same power level
Includes TSoIP / Native IP Transport inputs for ATSC 3.0 and DAB EDI interfaces
Efficiency-optimized – for highest efficiency and lowest cost of ownership
Variable speed fans to intelligently save energy
Hot-swappable, compact, high-efficiency DC power supplies
Hot-swappable, compact, high-efficiency power amplifiers
Incorporates the XTE-based Maxiva Compact exciter/driver for best-in-class performance
RoHS compliant / CE compliant
Support for all worldwide digital modulation standards
Modular & upgradeable architecture
All-digital linear and nonlinear pre-correction: Real-Time Adaptive Correction (RTAC)
Rugged, reliable design and construction
Broadband high-efficiency PA’s support redundancy and N+1 applications
Lowest energy usage
Minimum operating cost
';
XC Platform
';
MAXIVA™ XTE
Featuring unparalleled signal processing power, a smaller footprint and advanced Transport Stream over IP (TSoIP) input capabilities, Maxiva XTE builds upon a strong legacy of groundbreaking technological advances, pioneered by several decades of GatesAir innovations. Dramatically increased processing power together with new, advanced Real-Time Adaptive Correction (RTAC) techniques, provides optimum signal performance over a wide variety of modulations and RF amplifier topologies.
The Maxiva XTE supports a full range of digital broadcast standards, including ATSC, DVB-T/H, DVB-T2, ISDB-T, DTMB, DAB/DAB+/DMB. It is upgradeable to future new modulations, including ATSC 3.0, as they become available.
Main Features of Maxiva™ XTE
Advanced Real Time Adaptive Correction (RTAC)
Optimized correction for all amplifier types
Frequency Agile – Band I, III, IV and V
Supports all widely used TV standards and DAB/DAB+ radio
Upgradeable to emerging digital standards
Available Internal GNSS (GPS/GLONASS) receiver for precision frequency control and/or timing required for SFN
Available Internal UPS
Compact 1RU design
Dual redundant TSoIP inputs with seamless auto-switching
Dual redundant transport stream inputs with seamless auto-switching for ASI/T2MI
Integrated ISDB-Tb Remux
Seamless integration with GatesAir transmitters
Intuitive Web GUI interface with HTML
Advanced monitoring and diagnostics support
';
MAXIVA™ ULXTE
Optimized for International Markets The Maxiva ULXTE transmitter utilizes the latest 50-Volt LDMOS amplifier devices, new compact high-efficiency power supplies and the new Maxiva XTE exciter with advanced real-time adaptive correction (RTAC) for outstanding signal performance.
The Maxiva ULXTE power amplifiers have been optimized to provide the best possible performance and efficiency for both ATSC 1.0 and ATSC 3.0. The ULXTE transmitter is rated for identical average power levels for both modulations, assuring a simple and cost-effective upgrade path for future ATSC 3.0 operation.
Modular designs simplify installation and reduce ongoing maintenance, dramatically lowering total cost of ownership over the life of the transmitter.
Main Features of Maxiva™ ULXTE with PowerSmart® Plus The Maxiva ULXTE with PowerSmart® Plus is the highest efficiency broadband UHF transmitter on the market.
Up to 45% AC-to-RF efficiency Simple and cost-effective upgrade path from ATSC 1.0 to ATSC 3.0 at the same power level New high-efficiency DC power supplies Integrated high-efficiency pump system for certain power classes Hot-swappable light-weight PA modules Hot-swappable compact DC power supplies Incorporates the newest technology Maxiva XTE exciter for best-in-class adaptive pre-correction and native IP transport inputs RoHS compliant / CE compliant Support for all worldwide digital modulation standards Modular & upgradeable architecture All-digital linear and nonlinear pre-correction: Real-Time Adaptive Correction (RTAC) Rugged, reliable design and construction Ideal for N+1 configurations since all transmitters can be identical and use the same PA’s, minimizing spares requirements Lowest energy usage Minimum operating cost
';
MAXIVA™ UAXTE
Optimized for International Markets
The Maxiva UAXTE utilizes the latest generation 50 volt LDMOS amplifier devices, new compact high-efficiency power supplies and the Maxiva Compact series exciter/driver along with real-time adaptive correction (RTAC) for outstanding signal performance. The Maxiva UAXTE power amplifiers have been optimized to provide the best possible performance and efficiency for both ATSC 1.0 and ATSC 3.0. The UAXTE transmitter is rate for identical average power levels for both modulations, assuring a simple and cost-effective upgrade path for future ATSC 3.0 operation. The modular design further simplifies installation and reduces maintenance costs, dramatically lowering the total cost of ownership over the transmitters life-cycle.
The Maxiva UAXTE with PowerSmart Plus is an efficiency-optimized UHF transmitter. This all-new design includes several energy saving features.
Up to 44% AC-to-RF efficiency
Simple and cost-effective upgrade path from ATSC 1.0 to ATSC 3.0 at the same power level.
Efficiency-optimized – for highest efficiency and lowest cost of ownership
Variable speed fans to intelligently save energy
Hot-swappable, compact, high-efficiency DC power supplies
Hot-swappable, compact, high-efficiency power amplifiers
Incorporates the XTE-based Maxiva Compact exciter/driver for best-in-class performance
RoHS compliant / CE compliant
Support for all worldwide digital modulation standards
Modular & upgradeable architecture
All-digital linear and nonlinear pre-correction: Real-Time Adaptive Correction (RTAC)
Rugged, reliable design and construction
Ideal for N+1 configurations since all transmitters are identical and use the same PA’s, minimizing spares requirements
Lowest energy usage
Minimum operating cost
';
Master Control & Playout Services
Nextologies master control and playout operators have the ability to insert commercial spots and programming into any of our content partners live channels ensuring your schedule stays accurate and profitable.
Using our custom designed time shifting module, we can time shift your signal 24+ hours and into multiple time zones.
';
Medium power VHF tansmitters
The medium power transmitters of TVH4000 series incorporate power amplifiers based on LDMOS transistors technology characterized by high power density, allowing very high efficiency. They provide excellent values on key parameters of the transmitted signal quality, such as shoulder attenuation and MER.
They integrate a modulator that covers the main Digital TV and Radio systems, equipped with the latest technology in signal processing allowing Digital TV and Radio signal broadcasting with the highest quality and reliability.
The customer oriented and compact design provides full flexibility and multiple configurations per rack, saving a lot of space in the transmitter site. The rapid and easy stratup of the transmitter and the power of the Web Server ensures fast commissioning and easy operation. The different options for redundancy and optimal design of critical modules guarantee continuity of service throughout the life of the transmitter.
';
TV Transposers
';
TLWH7900 Series
The new High Efficiency-Wideband TLWH7900 Series represents a step ahead in the technology of high power UHF liquid cooled transmitters. For the first time the Doherty technology becomes Wideband, meaning that it is applicable to the whole UHF band.Therefore, no modifications in the amplifiers are required when the operator needs to change the RF channel.
TLWH7900 Series provides the optimal solution to operators that want to deploy or extend a digital broadcast network with HDTV, DTV and mobile TV channels globally. They offer an outstanding efficiency up to 42%, enabling a high economic benefit to broadcasters.
They are equipped with the most advanced technology in signal processing and the power amplifiers are based on LDMOS transistors – 50 volt. characterized by a high power density.
They feature a power-to-size and performance-to-reliability ratios that allow the signal broadcasting with the highest quality. Its compact and modular design as well as its high energy efficiency facilitate the installation and maintenance, thus significantly reducing the total expenditures over the life of the transmitter for the broadcast operator.
';
Anywave
Indoor Air Cooled & Liquid Cooled
Outdoor Tower Mounted Multichannel and Single Channel
ISDB-TB Exciters
Gap Fillers
Filters & Combiners
Couplers, Power Meters, Dummy Loads, RF Switches
PHASE - Serving the Brazilian Television Market since 1980
R&S®BSCC 5G broadcast service and control center
Rohde & Schwarz presents world’s first comprehensive 5G Broadcast solution at IBC 2019
The Rohde & Schwarz solution for the first complete 5G Broadcast transmission consists of the core network functionality provided by the new R&S BSCC broadcast service and control center and R&S Tx9 transmitters, which support FeMBMS. This all-in-one solution covers all entities from the content provider to the consumer and is fully compliant with 3GPP Release 14. R&S BSCC enables broadcasters for efficient distribution of high-quality video to the 5G ecosystem. The world’s first complete 5G Broadcast solution will be showcased at the Rohde & Schwarz booth B.21 in hall 7.
In recent years, media consumption has shifted significantly toward smartphones and other portable devices. Reaching the billions of smartphones around the world will be the future of broadcasting. 3GPP Release 14 is enabling this future by using FeMBMS (Further evolved Multimedia Broadcast Multicast Service). As a part of the Bavarian research project 5G TODAY, Rohde & Schwarz is investigating large-scale TV broadcasts in the FeMBMS mode. Using high-power high-tower (HPHT) transmitters allows broadcasters to distribute video over 5G networks in downlink-only mode with all the advantages of classic broadcasting. This provides the high quality levels known from HDTV broadcasting, low-latency live content as well as enormous spectrum efficiency and wide coverage. There is no need for a SIM card in the mobile device.
To help utilize all these benefits, Rohde & Schwarz is the first technology vendor worldwide to offer a complete 5G Broadcast solution for network operators. This solution covers all entities from the content provider to consumers. R&S Tx9 transmitters provide FeMBMS based on a unique software-based signal processing platform. The pure software-based signal processing platform gives network operators great flexibility and ideally prepares them for future signal processing requirements.
At IBC, Rohde & Schwarz is launching its new 5G Broadcast core network element, the R&S BSCC broadcast service and control center, which enables Rohde & Schwarz terrestrial transmitters to deliver LTE/5G Broadcast content. This element provides core network functionality so that network operators can distribute content over LTE/5G Broadcast. The main benefit of the R&S BSCC is that it reduces 3GPP core network entities’ complexity to meet broadcasters’ needs for a straightforward LTE/5G Broadcast experience. The overall Rohde & Schwarz solution makes it very easy to configure network parameters. Multiple Rohde & Schwarz FeMBMS transmission sites can be centrally configured in the R&S BSCC core network element.
';
R&S®TMU9
The R&S®TMU9 air-cooled transmitters attain output powers in from 300 W to 3.0 kW for digital standards and up to 4.75 kW for analog standards. The transmitters are accommodated in only on rack, saving a lot of space at the transmitter site.
With efficiency values of up to 30 % in normal mode, the transmitters save a great deal of energy and significantly reduce CO2 emissions. The Doherty architecture for boosting efficiency increases this figure to up to 42 %. These figures are unparalleled on the market, making the R&S®TMU9 transmitter familie the global benchmark for broadcast transmitters with optimized operating costs.
The transmitters feature unique system variability. Innovative configurations, such as MultiTX or N+1 systems in a single rack, and built-in bandpass filters ensure short delivery times even for special transmitter configurations. Excellent efficiency and the integration of multiple transmitters into a single rack reduce the total cost of ownership (TCO) of a transmitter system by more than half over the system’s lifetime.
';
R&S®THU9evo
';
R&S®TLU9 Transmitter and GapFiller Family
';
