The FRC0750 can also be used as an active switching device for signal routing purposes or redundancy switching operations. In its default configuration, the FRC0750 combines up to 4 different L-band signals into one L-band signal. As an option it is possible to combine up to 8 different L-band signals within the same unit.
A DC power supply and a reference frequency are also available on the L-band output, providing a compact and cost effective solution when the FRC0750 is used in combination with an outdoor RF upconverter and/or amplifier.
The FRC0750 can be delivered with an integrated block upconverter as option. In this configuration, the FRC0750 converts the L-band output signal of the combiner to C, Ku or DBS-band. The FRC0750 is easy to operate and monitor. All control and monitoring parameters are available locally on the front panel and remotely through a web interface. It is also possible to control or monitor the FRC0750 via Newtec’s proprietary RMCP protocol or via SNMP.
Key features
Up to 8 L-band inputs
Each input is switchable and gain adjustable
Optional upconversion to C, Ku or DBS-band
Optional 10 MHz +DC power for BUC
Optional 10 MHz reference input/output
Advanced monitoring and control
Other products from this company:
FRC0710 Upconverter
FRC0730 Up and Down Converter
HUB6504 4IF HUB MODULE
HUB7208/7303 XIF HUB MODULE
M6100 Broadcast Satellite Modulator
MCX7000 Multi-Carrier Satellite Gateway
New FRC0740 L-band Block Upconverter
New FRC0750 Active L-Band Combiner and...
SAT2210 Satellite Terminal
USS0202 Universal Redundancy Switch
USS0212 1+1 Redundancy Switch
FRC0710 Upconverter
The FRC0710 is easy to operate and monitor. All control and monitoring parameters are available locally on the front panel and remotely through a web interface. It is also possible to control or monitor the FRC0710 via RMCP or SNMP.
Key features
Agile IF to L-band Upconverter
Optional up-conversion to C, Ku or DBS-band
Ultra fine L-band frequency resolution (48Hz)
IF input frequency switchable between 70 MHZ & 140 MHz
Switchable spectrum inversion
Very high frequency stability
Very low spurious characteristics
Phase noise compliant with Intelsat IBS/ Eutelsat SMS
High linearity over the entire bandwidth
Optional 10 MHz + DC power for BUC
';
FRC0730 Up and Down Converter
Highest signal quality
Extensive coverage of all transponder frequencies
High flexibility
The FRC0730 offers some advanced and unique features such as a calibrated high linearity over the entire bandwidth combined with a very high frequency stability. These features make the FRC0730 the perfect solution for a wide range of transmissions ranging from very small carriers to full transponder applications.
The FRC0730 is easy to operate and monitor. All control and monitoring parameters are available locally on the front panel and remotely through a web interface. It is also possible to control or monitor the FRC0730 via RMCP or SNMP.
Key features
Agile IF to L-band Up & Down Converter
Optional up-conversion to C, Ku or DBS-band
Ultra fine frequency resolution
IF frequency switchable between 70 MHZ & 140 MHz
Very high frequency stability
Very low spurious characteristics
Phase noise compliant to Intelsat IBS/ Eutelsat SMS
High linearity over the entire bandwidth
Optional10 MHz + DC power for BUC
Optional LNB power supply + 10 MHz
';
HUB6504 4IF HUB MODULE
Hosting up-to 4 satellite networks in a single rack, the Newtec HUB6504 is the solution for satellite service providers. It enables any network configuration, from a single to multiple service areas, one or more satellites, different frequency bands, multiple transponders and High Throughput Satellites.
The modularity gives service providers agility to respond to their customer and market needs in a fast and cost effective way. Additional satellite networks can be added easily and rapidly. It only requires adding additional modulators, multicarrier demodulators and server blades into the preconfigured rack slots and activation in the Newtec Dialog Network Management System. High capacity multicarrier demodulator units can be added in function of the required capacity for SCPC, MF-TDMA and Newtec’s patented Mx-DMA return link technology.
Key features
Up to 4 satellite networks
Up to 60.000 terminals
Up to 800Mbps of satellite capacity, including all traffic processing
Support for SCPC, MF-TDMA and Mx-DMA® return links
Carrier grade reliability with built-in redundancy
Low initial cost, pay as you grow
60.000 terminals, 800Mbps satellite traffic, Carrier grade
The Hub Module can process up-to 60.000 terminals and 800 Mbps of satellite capacity. It includes all traffic processing, like Quality of Service and congestion management, acceleration, compression and encryption. The Hub Module easily integrates with the ‘IP backbone’ router and the RF gateway up/downlink. Built-in redundancy provides better than 99.99% platform availability.
';
HUB7208/7303 XIF HUB MODULE
The Newtec XIF Hub is the solution for gateway deployments serving a multitude of beams, transponders or satellites. The use of a baseband matrix brings N:M redundancy for up 32 multicarrier modulators and/or demodulators in one rack. In addition, the matrix fan in/out capabilities allows to simplify interfacing with the gateway RF infrastructure. Capacity can be extended easily and rapidly, simply by adding additional multicarrier modulators, demodulators and blade servers and activation in the Newtec Dialog Network Management System. High capacity multicarrier modulator units support DVB-S2X carriers, whereas the high capacity multicarrier demodulator units can support SCPC, MF-TDMA and Newtec’s patented Mx-DMA return link technology.
High Throughput
The Newtec XIF Hub is designed for operators seeking high throughput through its 10 Gbps Ethernet switching infrastructure. With support for Forward DVB-S2X carriers up to 500Mbaud, they can leverage the high bandwidth transponders provided by HTS satellites.
Key features:
Highly flexible and scalable hub architecture
Optimized baseband density & flexibility with baseband matrix
Up to 500 Mbaud forward carriers
Carrier grade reliability with built-in redundancy
Support for SCPC, MF-TDMA and Mx-DMA® return links
Pay-as-you-grow
';
M6100 Broadcast Satellite Modulator
Key features:
DVB-S2X, DVB-S2 and DVB-DSNG/S compliant
QPSK, 8PSK, 16/32/64/128/256APSK
Baud rate range: 0.05 – 72 Mbaud
Data rates up to 425 Mbit/s (in multistream mode)
Data rates up to 216 Mbit/s (in single stream mode)
Exceptional jitter recovery on TS over IP inputs
Automatic rate synchronization on TS over IP inputs
Null packet stuffing rate detector on incoming TS
Built-in TS Analyser with PCR jitter measurements and monitoring of critical ECM/EMM messages
RFI reduction using optional DVB RF Carrier ID (DVB-CID) and NIT table CID (default)
Optional BISS Content protection
Optional redundant ASI transport stream interfaces
Redundant GbE interfaces with SMPTE 2022-1/2 FEC error correction
Built-in source redundancy, supporting any redundant IP network configuration
External reference input
IF (70/140) and L-Band (950-2150) high power outputs
Optional integrated RF upconverter (Ku-band or C-band)
L-band monitoring output
Market leading RF purity and performance
Clean Channel Technology®
Optional linear and non-linear Equalink® 3 Pre
Main advantages:
Support of the latest and most efficient DVB-S2X standard
Highest system reliability and service uptime through robust design and industry leading redundancy solutions
Low total cost of ownership as a result of very high bandwidth efficiency technology options, and ease of monitoring and control
Clean Channel Technology® provides up to 15% bandwidth efficiency gains on top of the DVB-S2 standard
Equalink® 3 pre-distortion provides up to 10% bandwidth gains, higher QoS or geographic coverage
Built-in support for opportunistic data insertion, interoperable with IRD’s that support Multi Protocol Encapsulation (MPE)
Easy integration with industry leading management systems (EMS/NMS/OSS)
Safe investment as the platform supports advanced capabilities such as proMPEG FEC on inputs and outputs, built-in transport stream analyzer and DVB & NIT Carrier ID
Pay-as-you-grow flexible licensing scheme
Future-proof design combining video and IP multi-service capabilities, supports transport of today´s and tomorrow´s services
Dedicated Graphical User Interfaces for single stream and multistream applications:
- For your single stream applications: M6100 Broadcast Satellite Modulator R2.11
- For your multistream projects: M6100 Broadcast Satellite Modulator R2.1
';
MCX7000 Multi-Carrier Satellite Gateway
Main advantages:
The Newtec MCX7000 is a new dense DVB-S2X multi-carrier satellite gateway for efficient distribution to towers and headends, or for use in back-up or dense DTH HUB stations, resulting in OPEX and CAPEX savings. This 133 Mbaud modem is also fit for broadcast contribution applications on standard and HTS spotbeam transponders.
Compatible with the Newtec Dialog® multiservice broadcast platform, it brings increased bandwidth efficiency of up to 51% and features multistream, as well as Newtec's Clean Channel Technology® and its linear and non-linear pre-distortion technology Equalink® 3.
Building upon the MDM6100 Broadcast Satellite Modem software suite, the enhanced hardware platform of the MCX7000 extends the modem capabilities beyond single carrier support.
In a multi-modulator configuration, four 133 Mbaud carriers acc. DVB standards up to DVB-S2X can be generated. Efficient transmission of UHDTV bouquets over 2 or 3 transponders for DTH only requires the Channel Bonding license.
In a multi-demod modem configuration, two 133 Mbaud carriers can be demodulated, next to modulation of a 133 Mbaud signal with full support of the DVB satellite standards up to DVB-S2X. Each and every Transport Stream embedded in one of the received carriers can be output on one of the six (optional) ASI or dual Ethernet ports. The same data interfaces can be used as input ports for the modulator.
Transmodulation of a received stream is also an option.
Its remote in-band management and software upgradeability makes it the receiver equipment of choice for remote unattended towers and headends. Subsequent releases of this future-proof DVB-S2X platform guarantee, by simple software upgrade, even increased functionality and higher density.
Key features:
Maximum configurations:
- 4 x DVB-S2X carrier modulator
- 3 x DVB-S2X carrier modulator with optional ASI interfaces
- 2 x DVB-S2X carrier modulator and one demodulator with optional ASI interfaces
- 3 x DVB-S2X carrier demodulator (with dual L-band input)
- 2 x DVB-S2X carrier demodulator with one modulator and optional ASI interfaces
Minimum symbol rate: 256 kbaud
Maximum symbol rate: 133 Mbaud
Data rates up to 425 Mbit/s
IF (70/140) and L-Band (950-2150) high power outputs
Very high bandwidth efficiency, ease of monitoring and control leads to Low Total Cost of Ownership
- DVB-S2X, DVB-S2, DVB-DSNG/S compliant
- QPSK, 8PSK, 16APSK, 32APSK, 64APSK, 128APSK and 256 APSK
- Up to 15% bandwidth gain with optional Equalink® 3 pre-distortion
- Up to 15% bandwidth efficiency gains (on top of DVB-S2) with Clean Channel Technology®
- Multistream CCM or VCM mode with ISSY
Highest system reliability and service uptime
- Redundancy with main TS over ASI and back-up TS over IP input
- Optional Seamless Switching acc. SMPTE 2022-7 on TS over IP inputs
- Carrier-based redundancy switching in a multiple modulator 1:1 configuration
- TS null packet stuffing detector
- Built-in TS Analyser with PCR jitter measurements
- RFI reduction using optional DVB RF Carrier ID (DVB-CID) and NIT table CID (default)
- Market leading RF purity and performance
- PRBS generator for link performance tests
Remote in-band management
Remote over-the-air software upgrade
Optional 4 x MPE encapsulators / decapsulators up to 70 Mbps
Optional AES encryption / decryption up to 140 Mbps
Optional BISS scrambler/descrambler up to 130 Mbps
Optional DVB-S2X Channel Bonding modulator up to 425 Mbps
';
New FRC0740 L-band Block Upconverter
The FRC0740 is easy to operate and monitor. All control and monitoring parameters are available locally on the front panel and remotely through a web interface. It is also possible to control or monitor the FRC0740 via RMCP or SNMP.
Key features
Wide choice of RF frequency ranges covering C, Ku and DBS-bands
Very high frequency stability
Very low spurious characteristics
2 L-band inputs and one L-band output
Integrated signal combiner
Very high linearity
Very good gain flatness over the entire bandwidth
';
New FRC0750 Active L-Band Combiner and Upconverter
A DC power supply and a reference frequency are also available on the L-band output, providing a compact and cost effective solution when the FRC0750 is used in combination with an outdoor RF upconverter and/or amplifier.
The FRC0750 can be delivered with an integrated block upconverter as option. In this configuration, the FRC0750 converts the L-band output signal of the combiner to C, Ku or DBS-band. The FRC0750 is easy to operate and monitor. All control and monitoring parameters are available locally on the front panel and remotely through a web interface. It is also possible to control or monitor the FRC0750 via Newtec’s proprietary RMCP protocol or via SNMP.
Key features
Up to 8 L-band inputs
Each input is switchable and gain adjustable
Optional upconversion to C, Ku or DBS-band
Optional 10 MHz +DC power for BUC
Optional 10 MHz reference input/output
Advanced monitoring and control
';
SAT2210 Satellite Terminal
Thanks to a unique design of both the compact modem and the iLNB, the cost of the terminal is kept to a minimum.
The IP Satellite Modem is available with unique Point & Play® easy-install technology, supporting the installation of the complete terminal without specific qualifications or expensive tools. Point&Play provides correct satellite identification and facilitates pointing. This can happen through audio feedback, or through the Terminal Installation App. This smartphone app connects to the modem through Wi-Fi. It supports a number of key functionalities required during an antenna installation: Site acceptance, polarization adjustment, fully aided antenna pointing, storm testing etc. After mounting and positioning, the integrated certification assures correct installation by giving instant link quality approval. It guarantees that each terminal works at maximum efficiency without any interference risk.
Key Features:
Small size, table top or wall mounted
Optional Wi-Fi and advanced routing support
Wideband DVB-S2X ACM Forward
4CPM MF-TDMA Adaptive Return Link
Embedded TCP acceleration and encryption
Multi-level Quality of Service
Layer 2 and Layer 3 support with versatile IP routing and addressing
Low jitter for real time applications
DNS Cache/Relay
Support of IPv4 and IPv6
Multiple virtual networks behind the modem
Over-the-air software upgradeability
Over-the-air monitoring and diagnostics tools
Dual satellite configuration settings
Ka- and Ku-band terminal solutions
Support for single cable iLNBs
';
USS0202 Universal Redundancy Switch
Dual redundant power supply with monitoring
From 1+1 to 16+1 configuration
Automatic or manual operational mode
GbE Logical Switching
Automatic Switch Back
Copy the full configuration from a device to another
Automatic memorization of configuration
Reference device
GUI with synoptic view
User-configurable switching logic
Operates and controls up to 36 switching modules
Switchable signals: ASI, IP, IF, L-band and RF-band
Stand alone operation or integrated in a network management system
Monitoring & Control via SNMP
Management of Device Configuration
Main Advantages
High reliability through the dual redundant power supply – Main & Extension unit
Increases service availability significantly thanks to the automatic or manual operational mode, the Automatic Switch Back and the automatic memorisation of the configuration
Optimised switching time
Cost-effective solution through GbE logical switching
Future-proof solution thanks to its scalability from a 1+1 to a 16+1 configuration
Easy setup and installation through the ability to copy the full configuration from one device to another
Flexible deployment and device hot replacement
Easy to use, control and operate through its user-configurable switching logic and the Automatic Switch Back
Easy integration into NMS systems through SNMP
Highly compact
';
USS0212 1+1 Redundancy Switch
High reliability through the dual redundant power supply
Increases service availability significantly thanks to the automatic or manual operational mode, the Automatic Switch Back and the automatic memorisation of the configuration
Cost-effective solution through GbE logical switching
Easy setup and installation through the ability to copy the full configuration from one device to another
Easy to use, control and operate through its user-configurable switching logic and the Automatic Switch Back
Easy integration into NMS systems through Monitoring & Control via SNMP
Highly compact
Key features
Dual redundant power supply with monitoring
Automatic or manual operational mode
Logical Ethernet switching
Automatic Switch Back
Copy the full configuration between devices
Automatic memorization of configuration
Reference device
GUI with synoptic view
User-configurable switching logic
Switching of ASI, IP, IF, L-band and RF signals
Stand alone operation or integrated in a network management system
Monitoring & control via SNMP
Management of device configuration
';
Related Products:
Alchemist Live IP
Neuron IP processing
FastTICO-XS SDK
DA-HDTV-USB Frame Grabber
IF8K-FSCC
MCC-4K-A
IP Virtual Card
greenMachine HDR Evie+
LiveU LU600 HEVC – UBMS
Smart-telecaster Zao-S
Cosmos
TICO-XS IP cores
Atomos AtomX Modules
Atomos Connect Converters
Bluefish444 Synapse HDMI120 Mini Converter
Bluefish444 Synapse ANA140 Mini Converter
Bluefish444 Synapse SDI110 Mini Converter
Master Sync Generators
ULTRA Sereis 4K/8K TICO Codecs &...
Video Connect
FRC0730 Up and Down Converter
New FRC0740 L-band Block Upconverter
New FRC0750 Active L-Band Combiner and...
UHD Scaling Cross Converter
Alchemist Live IP
Alchemist Live from Grass Valley, a Belden Brand, offers the very best motion compensated framerate conversion, providing transparent, artifact-free conversion for seamless global distribution of live media.
Neuron IP processing
';
ETH-LANC Link
Control your Sony cameras such as FS5, FS7 and other LANC compatible cameras (any camera the Sony RM-BP30 supports). Or use the ETH-LANC Link to control Canon cameras that speaks the RC-V100 Protocol such as the C Series, XF Series and ME Series.
Features
- 2.5 mm connector
- LANC Protocol or Canon RC-V100 Protocol
- Camera Selector
- Ethernet with PoE (IEEE802.3af)
- Made in Denmark
';
FastTICO-XS SDK
Available for CPU or GPU, implementing the newJPEG-XS standardand many more features, the intoPIX FastTICO-XS SDKs provide the highest quality, lowest latency, visually lossless codec for the optimization of your application. FastTICO-XS SDKs are perfect for all professionals looking to deploy ultra-low latency, lossless encoding over their whole infrastructure and workflows.
Feature overview
Quality & latency
- Best-in-class visually lossless video codec , compliant with JPEG XS
- Adjustable compression ratio (on frame by frame) with constant bitrate throughput (CBR)
- From Lossless down to near-lossless / visually lossless
- Ultra-low latency capability (down to only few lines in CPU) with an optimal API
- Optimized for real-time operations
Processors (CPU / GPU)
- Highly parallelized processing in encode/decode
- x86-64 Intel / AMD CPU (SSE 4.1, AVX2 or newer) in CPU
- Nvidia GPU (CUDA)
Image formats & frame rates
- Supports monochrome (4:0:0, Alpha) up to 16bit,
- Support 4:2:2 and 4:4:4 8/10/12 bit
- Validated up 8K UHDTV-1 (8192)
- Frame rate depends on CPU/GPU performance & SDK packages
Compression
- Compliant with JPEG XS standard & profiles
- Additional advanced features by intoPIX improving performances & quality.
Rate control
- Adjustable compression rate
- Constant (predictable) bitrate (CBR)
Operating systems
- Windows & Linux (32-bit/64-bit) + macOS (64 bit)
Add-ons
- Embedded Downscaler Add-On: Proxy x1 & x2 decoding (ie. decode directly HD resolution or 4K resolution from 8K XS-compressed video stream) and reduce your CPU or GPU load.
- FFmpeg Add-On : connect directly the intoPIX SDK to FFmpeg
- Insertion/Extraction of Color Specification box / Video Support box from JPEG-XS part 3
- SDI Mapping Add-On: enables users to map 4K/8K effciently over existing 3G/HD-SDI cables. This unique feature reformats the XS codestream to fully map the SDI active area avoiding the forbidden EAV/SAV codes, offering a 20% gain of compression/quality performances.
DA-HDTV-USB Frame Grabber
- This compact box - with a magnetic bottom for an easy installation on a metal surface or using the supplied mounting plate, accepts HDMI or SDI input signals and streams them to its USB 3.1 output.
- It accepts HDMI 2.0 signals video resolutions up to 4K/UHD 60 Hz (4:4:4) and SDI signals up to 3G-SDI (1080p60) and has loop out outputs for both. The USB 3.1 streaming output maximum resolution is 1080p60 (meaning that 4K/UHD signals are down converted to 1080p).
- It works with software media players such as VLC and other conferencing applications. It is very easy to set up: Just connect it, launch the media player or conferencing application and select the device as audio and video source. You can then record or stream the DA-HDTV-USB video and audio signals. It is compatible with Windows, MAC and Linux computers.
- It has a mic input allowing to mix voice with the input audio and a speaker output allowing to check the audio output.
- All the necessary cables and accessories are supplied as standard.
IF8K-UCN
The IF8K-UCN is a frame synchronizer that supports upconversion of HD/4K UHD to 8K DG (Dual Green). It inputs HD-SDI or quad-link 3G-SDI (3G-SDI x 4) and outputs octa-link 3G-SDI (3G-SDI x 8) signals. Two-way distribution of 8K DG is standard and BB or Tri-level sync reference input is also supported. It is designed and manufactured by InSync Technology for exclusive distribution by FOR-A.
The IF8K-UCN is an ideal solution for integration of HD or 4K UHD material into 8K UHD productions using the dual-green format.
Key features:
- Frame synchronisation to an external reference with tracking PCM audio delay
- Minimum delay mode (no reference) – lock to input
- Very high quality upconversion with filter control.
- Conversion between 59.94 and 60Hz conversion (Drops or repeats 1 frame in 1000 frames)
- Optional remote control via IF8K-REMOTE
';
IF8K-FSCC
The IF8K-FSCC synchronizes full 8K video with both 12G-SDI and 3G-SDI signals. Asynchronous input of quad-link 12G-SDI (12G-SDI x 4) or 16 link 3G-SDI (3G-SDI x 16) for 8K can be synchronized by the external reference input and output with quad-link 12G-SDI. It is designed and manufactured by InSync Technology for exclusive distribution by FOR-A.
The IF8K-FSCC is an ideal solution for 8K synchronisation and colour correction. It’s especially valuable where perfect synchronisation without audio disturbance is needed in live 8K productions.
Key features:
- Video signal processing of the luminance level, chroma level, chroma phase, and black level
- Colour corrector to set white balance, black balance, and color gamut
- Horizontal/vertical phase adjustment by the external reference input
- Additional audio delay for upstream or downstream equipment for each audio channel
- MADI audio input/output interface
- Optional remote control via IF8K-REMOTE
';
MCC-4K-A
The MCC-4K-A provides exceptional quality frame rate and format conversion for UHD/3G/HD signals. MCC-4K-A offers support for quad link 3G-SDI of two-Sample Interleaved (2SI) or Square Division (SQD) format as well as single link 12G/6G-SDI and SFP connectivity.
The MCC-4K-A is an ideal solution for live frame rate conversion applications, where UHD content sourced at a chosen production rate needs to be converted to other frame rates for international contribution and distribution. International sports, concerts, breaking news and current affairs can all be simply and impeccably converted to the desired output format and frame rate.
Key features:
- Motion compensated conversion from any UHD frame rate to any other UHD frame rate
- Simultaneous UHD single link 12G/6G and UHD quad link 3G-SDI output
- Automatic detection of SMPTE ST425-5 (sample interleave input) and ITU-R BT.2020 colorimetry
- Motion compensated conversion from any 3G/HD-SDI frame rate to any other 3G/HD-SDI frame rate
- Up-conversion from 3G/HD to UHD
- Down-conversion UHD to 3G/HD
- HDR/SDR conversions
';
IP Virtual Card
Besides the well-known VideoMaster SDK dealing with the DELTACAST I/O cards and FLEX products, the DELTACAST portfolio now includes a new SDK (Software Development Kit) component called the IP Virtual Card, offering a new programming interface named VideoMaster IP.
The IP Virtual Card is a new video and multimedia programming interface allowing the use of 3rd-party computer network cards to capture and stream out video just like you are used to do over any DELTACAST card.
Designed from the ground up to allow high-performances multimedia capture and streaming using an off-the-shelf network card, the first version ofthe IP Virtual Card targets ST2110 connectivity.
The IP Virtual Card brings in support for video transport as per ST2110-20, audio transport as per ST2110-30, and ancillary data transport as per ST2110-40. It also includes a PTP synchronization solution compliant to ST2059-1. Thanks to an optimized network stack, the IP Virtual Card insures accurate, PTP locked, media streams compliant to ST2110-21 Type W senders, and it allows implementing ST2110-21 Type A receivers.
The IP Virtual Card implements an optimized network stack based on the operating system sockets, so that it is compatible with any NIC brand and model, and so that it can be used under Windows and Linux, and also targetting virtualization environments and execution in containers. For most demanding applications, the IP Virtual Card also exists in a version based on the DPDK kernel bypass.
Using the IP Virtual Card features requires installing a license. Please contact us for further details about this.
';
greenMachine HDR Evie+
The greenMachine HDR Evie+ (Enhanced Video Image Engine), 1 RU half 19” rackmount, is a real-time segmented frame-by-frame broadcast-quality High Dynamic Range (HDR) to Standard Dynamic Range (SDR) converter, with frame sync supporting formats up to 4K UHD (3840x2160). It is the world’s first system that uses the advanced algorithm for sectional dynamic tone mapping, which automatically analyzes different sections of an image in HDR stream and applies optimal corrections on a frame by frame basis in real-time. This unique capability is unlike any other solution today. It is the perfect real-time production tool for sports or any live broadcast event needing high-quality real-time HDR to SDR conversions. HDR EVIE+ fits best in the single native HDR workflow reducing the cost of equipment and manual operations.
The sectional dynamic tone mapping technique is applied to several spatial areas (sectors) in the image. In this type of tone mapping technique, the algorithm adjusts the signal by using several dynamic curves, one per image segment/sector. The algorithm then combines the result with global dynamic curves based on the entire image. While the dynamic curves of the different sectors are perfectly adapted to the respective image content of their segments, the global curve is perfectly adapted to the content of the entire image. Depending on the image content within these sectors, the algorithm reacts dynamically, which allows lights and shadows to be treated independently. Therefore, dark areas can be brightened, and the bright areas can be darkened without getting a flat gradation of the image. “
HDR EVIE+ provides a 1x 4K/UHD processing channel supporting down-conversion from HDR transfer characteristics to SDR through appropriate sectional dynamic tone mapping. It also supports the Wide Color Gamut (WCG) needs of broadcasters and professional AV live events requirements. HDR Evie+ package also includes HDR Static configuration for Static HDR SDR conversions, which performs static tone mapping to realize UP/Down/Cross conversions between HDR and SDR, suited best for the studios or the environments where the light conditions do not change dynamically.
LiveU LU600 HEVC – UBMS
The LU600 is LiveU’s flagship portable transmission unit for global newsgathering, live sports and events coverage. Combined with the 4K HEVC Pro Card, the LU600 delivers unparalleled video performance with extreme bandwidth efficiency – in one of the smallest portable cellular bonding units in the market.
ULTIMATE VIDEO QUALITY
The LU600 HEVC delivers the highest video quality and bitrate in the market (up to 20Mbps), fastest file transfer (60Mbps) and lowest delay.
Using the LU600 HEVC, broadcasters can provide the same video quality as H.264 while using about half the bandwidth, or offering greatly improved video quality wherever original H.264 bitrate is maintained.
BUILT FOR YOUR NEEDS
Tailored to the needs of mobile journalists, the LU600 HEVC product suite offers three configurations, including: HD, 4K-HDMI and 4K-SDI.
The unit comes in a specially designed smart backpack, with improved usability, remote control functionality and easy access to display, controls and interfaces.
ADVANTAGES
- Superior 1080/4K video quality based on broadcast-grade hardware encoding – supporting VR and 360 degree applications
- Very low power consumption, with 4 hours of battery time
- Dynamic bitrate and resolution changes on the fly
- HEVC and H.264 file encoding capability for production workflows
- ‘Live & Store‘, allowing broadcasters to go live under any network conditions while simultaneously saving a high-quality copy of the live video for future purposes.
- High speed bonded internet capabilities
- 5” LCD with ultra-responsive capacitive touchscreen
';
Smart-telecaster Zao-S
The Zao-S is a portable video H.265 HEVC encoder that compresses video in real-time, enabling full HD live video streaming to anywhere from anywhere, all while on the move. The equipped H.265 video compression is the most efficient standard for encoding and compression on the market today. As a result, the Zao-S enables constant HD video quality, low latency, and the freedom to transmit live video from across the globe. The Zao-S is made in Japan and features the high quality craftsmanship that Japanese products are known for. The Zao-S is constantly being improved as our engineers develop new features and increase its capabilities.
Sophisticated Multi-Network Bonding Technology - RASCOW
The Zao-S allows up to 3 external USB modems to be bonded together to form a single connection via 4G, 5G, Wi-Fi, and/or satellite. When transmitting video live over the mobile network, many factors such as the carriers being used, cell tower locations, and varying bandwidth levels affect video quality. Our proprietary protocol, RASCOW, monitors these factors along with the changing mobile signal strength in real-time and adapts the most optimum bonded combination of the network connections. The Zao-S, with the RASCOW protocol, continues to reliably send high quality video even when signal strengths become low or fluctuate rapidly.
Sleek. Compact. Mobile.
The Zao-S maximizes mobility without sacrificing quality. Due to its lightness (about 350g) and portability, the Zao-S can be carried with a body strap or be mounted on a camera. The compact design, and one hour internal battery, make the Zao-S an excellent choice for drone applications as well.
';
Cosmos
Cosmos provides software based playout engines for Broadcasters, Over The Top service providers and Broadcast Services companies.
The distributive virtualised architecture of the playout engine from Cosmos provides a fast and trusted cloud based playout solution enabling broadcasters and service providers to spin up both OTT and traditional TV channels in a few minutes thus lowering the cost of ownership.
Channels can be hosted from data centres or from your own Master Control Room over a private or public cloud. Cosmos also gives you the ability to playout both file based and live services .
Cosmos is an open system which enables all the features of a playout engine be implemented on a service basis. Cosmos reduces the need to invest in capital infrastructure. It removes the need to find space for technical equipment and the ongoing cost of technical maintenance.
Channel owners in worldwide gain the freedom to outsource practically all the technical equipment traditionally required for broadcasting.
Cosmos virtualises the process of channel management under control from a standard enterprise computer via a firewall-protected secure internet connection. Programme playout can be automated to any required extent while always retaining the freedom to insert live content.
Cosmos offers established broadcasters and content owners the ability to introduce new programme channels at very short notice, whether a permanent additional to an existing bouquet or a supplementary programme stream covering a temporary event. It can be matched to a wide variety of deployment models, enabling consistent operation across baseband, hybrid IP, and virtualised, cloud-based networks.
Cosmos also enables independent content producers to establish television channels without the high start-up cost usually inherent in such ventures.
Cosmos delivers unsurpassed flexibility in format handling and transcoding. It supports practically any technical standard in today's fast-evolving television industry, whether for terrestrial, satellite or online viewing, live, near-live or catch-up.
';
VICO-4L
Key features:
- Low latency 32 video lines fixed delay, or according to Genlock/FrameSync
- Compression ratio 4:1(4K3G-SDI), 8:1(4KHD-SDI)
- High image quality high peak signal to noise ratio (PSNR)
- Standardized SMPTE RDD 35 (TICO Alliance)
- 1 RU rack mount size (max dual channel)
Application areas
- Contribution
- Storage cost reduction to storage 1/4. 1/8
- OEM board can be provided
Technical specifications
SDI input BNC 75Ω 3G-SDI Level A 2SI, 12G-SDI Chroma 4:2:2 Bit Depth 10Bits Frame rate 50P(4:1 only), 59.94P, 60P Encoder input 4K (4 x 3G-SDI), 4K(1x12G-SDI) Decoder output 4K (4 x 3G-SDI)、4K(1x12G-SDI) Signal split mode INTER(2SI: 2 sample interleave division) Dimensions (ｍｍ) 435W x 260D x 44.5H Power supply AC 100～240V Power consumption 30VA Weight About 3.0Kg Operation temperature ０～35℃ Operation humidity 20 to 80% RH * No condensation
';
TICO-XS IP cores
TICO-XS is a smart upgrade path to manage higher resolutions (4K, 8K, …) and frame rates while assuring visual quality, keeping power and bandwidth at a reasonable budget and significantly reducing the complexity and cost of a system, a chip or an infrastructure.
Applications:
From 3G-SDI to IP in 4K
The mapping of the TICO-XS mezzanine compression to carry UHDTV 4K 60P over a single 3G-SDI cable has been specified in the SMPTE RDD35. intoPIX provides the needed building blocks to create a 4K over 3G-SDI solutions. Have a look at the intoPIX TICO-XS IP-cores and peripheral IP to map the compression over SDI.
4K with TICO compression over SMPTE2022-6
As SMPTE ST2022-6, defines the transport of HD-SDI or 3G-SDI over IP, using TICO-XS, it is easy to leverage an existing SMPTE 2022-6 system to carry up to three UHDTV 4K 60P streams over a single 10 GbE port using the SMPTE 2022-6 standard.
SMPTE 2110 and TICO compression
SMPTE ST2110-22 specifies the transport of compressed video over IP (including JPEG-XS), enabling you to transport any video formats over IP with full flexibility and all the benefits of TICO-XS compression.
8K over a single 10GbE
It has already been proven. TICO-XS can enable you to carry with lossless quality a 8K 60fps video stream over a single 10GbE link using TICO RTP payload and a SMPTE 2110-22 transport.
8K over a single 12G-SDI
It has already been proven. TICO-XS can enable you to carry a 8K 60fps video stream over a single 12G-SDI link with lossless quality.
TCP Link for ATEM
BlackMagic Design ATEM switcher has no TCP interface for easy integration with AV-systems, so SKAARHOJ has created this tool, the TCP Link for ATEM, which provides just that: A simple TCP interface to almost any feature in the switcher. It will report state changes of the switcher and accept and forward commands to the switcher. Exactly what you need for AV projects with various AV systems like Crestron, Extron, and so forth. Connect to the device via TCP, then change the desired command on the ATEM switcher and the TCP Link for ATEM will output in the terminal how the command looks that you can use to send the same command to the switcher.
Features
- Small rugged form factor
- Report state changes
- Send commands to ATEM Switcher
- Connect via TCP
- Made in Denmark
';
ETH-SDI Link
Receives “UDP Camera Control” information over Ethernet and forwards it on the SDI out connector.
Used to merge network data from multiple RCPs onto a single SDI wire.
Features
- BlackMagic 3G-SDI for ETH-SDI Link
- Alternative Firmwares for ETH-SDI Link
- Single Controller multiple returns
- Multiple Controller single return
- Made in Denmark
';
ETH-GPI Link
Setting up an I/O device have never been this flexible. Connect and control anything from your tally lamps, trigger ATEM switcher routines, control a HyperDeck, change Scopes on a SmartScope Duo and route inputs/outputs on a VideoHub. Defining parameters – single or multiple - for inputs/outputs is extremely fast, thanks to the drop-down menu structure in UniSketch OS. Connect and control up to 8 devices at the same time!
The general-purpose I/O controllers offer 8/16 inputs and 8/16 outputs, all electrically separated with quality relays and optocouplers. GPO is implemented with relays shorting to GND. GPI implemented with optical isolators shorted to GND.
Please notice: SKAARHOJ Controllers with GPI inputs accept open collector and relay outputs (pulled to GND). The default HD15 tally connector on the TriCaster TC1 does not provide a direct working signal to the ETH-GPI Link. Converting the 5V potential to GND is needed.
Features
- 1 x DB25 Connector Configuration
- 8 GPO
- 8 GPI
- Ethernet with PoE (IEEE802.3af)
- Made in Denmark
';
Atomos AtomX Modules
The AtomX Ethernet/NDI Expansion Module for Ninja V from Atomos provides a GigE connector supporting NDI input and output with encode, decode, control, and sync capability, allowing you to transmit, distribute, or receive and monitor NDI from any NDI source. The module connects to the Ninja V\'s AtomX expansion port. After it\'s attached, it also becomes the Ninja\'s battery plate. It accepts the Ninja\'s battery, which then powers both devices at the same time.
The AtomX SYNC Expansion Module for Ninja V from Atomos adds wireless timecode, sync, and Bluetooth control to the Ninja V monitor. You can sync and/or control 1000+ Ninja V units equipped with these modules on the same network at ranges up to 984\' in efficient multicam shoots.
';
Atomos Connect Converters
The Atomos Connect Convert line comes colour coded and forms a comprehensive and versatile lineup of 15 different conversion, signal processing and system integration boxes that connect, convert, scale, sync, split and repeat your video signals. The new lineup of Connect converters is not to be confused with the already existing Connect H2S HDMI to SDI and visa versa. The new lineup of Connect Convert devices feature a robust construction with locking DC and HDMI connectors, USB power and detachable mounting ears. Status is clearly displayed on bright LEDs and they can be quickly and easily configured using the free ConnectOS software.
';
Bluefish444 Synapse HDMI120 Mini Converter
The HDMI120 Synapse Mini Converter is Bluefish444’s SDI to HDMI video and audio signal processor for professional video workflows. The Synapse HDMI120 allows conversions from SDI signals to HDMI, and AES/ANA/SDI embedded audio input to HDMI embedded audio output.
Featuring the same high-quality standards as our video cards, the Synapse Mini Converter range offers a range of conversions, video scaling and PsF mode via configurable DIP switches, and an HDMI copy input & SDI copy output for redundancy.
Easy-to-use
- DIP switches allow for configuration of converter
Maximum Connectivity
- HDMi input with 8 channels of embedded audio
- Second HDMI input for redundancy
- 2 x 3G/HD/SD-SDI Outputs
- AES digital stereo audio input
- Analogue stereo audio input
';
Bluefish444 Synapse ANA140 Mini Converter
The ANA140 Synapse Mini Converter is Bluefish444’s analogue to SDI video and audio signal processor for professional video workflows. The Synapse ANA140 allows conversions from Composite, Component SD/HD, and S-video signals to 3G-SDI, and AES/ANA audio input to SDI-embedded audio output.
Featuring the same high-quality standards as our video cards, the Synapse Mini Converter range offers a range of conversions, video scaling and PsF mode via configurable DIP switches, and an SDI copy output for redundancy.
Easy-to-use
- DIP switches allow for configuration of converter
Maximum Connectivity
- Composite Video input
- Component Video input
- S-video input
- 2 x 3G/HD/SD-SDI Outputs
- AES digital stereo audio input
- Analogue stereo audio input
';
Bluefish444 Synapse SDI110 Mini Converter
The SDI110 Synapse Mini Converter is Bluefish444’s SDI to HDMI video and audio signal processor for professional video workflows. The Synapse SDI110 allows conversions from HDMI video signals to 3G/HD/SD SDI, and SDi-embedded audio input to HDMI embedded audio, AES digital stereo or Analogue stereo audio output.
Featuring the same high-quality standards as our video cards, the Synapse Mini Converter range offers a range of conversions, video scaling and PsF mode via configurable DIP switches, and an SDI copy input and output for redundancy.
Easy-to-use
- DIP switches allow for configuration of converter
Maximum Connectivity
- 3G/HD/SD-SDI input with embedded audio
- Second 3G/HD/SD-SDI input for redundancy
- SDI loop output
- HDMI output
- AES digital stereo audio output
- Analogue stereo audio output
';
Master Sync Generators
The SRG-series Master Sync Generators support a wide range of output signals and formats from composite to UHD. These reference generators can even provide multiple video standards simultaneously. Integrated video pattern generators with idents and motion are great for remote feeds.
Built to last and redundancy in mind, Ross Sync Generators will keep the heartbeat of your facility alive. All units feature redundant power and easy servicing. Automatic changeover units are available to ensure you never skip a beat.
GearLite
Gearlite point-of-use modules let you put them right where you need them. Every GearLite module ships standard with flexible mounting accessories and a universal power supply. They feature a compact design, so they fit almost anywhere, be it in a rack, on stage, behind a monitor or in a fly pack.
Small and compact doesn’t mean you need to settle for lower-grade processing. Our GearLite mini converter and distribution modules are built using the same high quality components and processing as our modular solutions, giving you broadcast-grade signal handling for SDI, 3G-SDI, 12G-SDI, fiber, audio and HDMI.
';
Evertz
Fiber Optics, CC, Multiviewers
RF Routing
Modular Products
PHASE - Serving the Brazilian Television Market since 1980
ULTRA Sereis 4K/8K TICO Codecs & Converters
';
Video Connect
Our video network platform is designed specifically for the optimal transport of video content and can receive and deliver signals of any format. Our expansive global reach, coupled with the ability to transport secure, broadcast-quality video over public IP, means we can reliably distribute content anywhere in the world.
CONNECT TO LEADING BROADCASTERS
GTT is located in the world’s most prominent studios, distribution head-ends, transmission facilities, teleports, public switches and data centers. We can provide direct, private and secure connectivity, ensuring the highest possible performance for your mission-critical content and services.
LOWEST LATENCY FOR LIVE VIDEO
For live interviews, remote production, or delivery to online gaming platforms, you need a high-speed, dedicated network path that you can rely on for seamless video transport. GTT owns and operates many low-latency routes, including the fastest fiber optic path between North America and Europe.
FRC0730 Up and Down Converter
Highest signal quality
Extensive coverage of all transponder frequencies
High flexibility
The FRC0730 offers some advanced and unique features such as a calibrated high linearity over the entire bandwidth combined with a very high frequency stability. These features make the FRC0730 the perfect solution for a wide range of transmissions ranging from very small carriers to full transponder applications.
The FRC0730 is easy to operate and monitor. All control and monitoring parameters are available locally on the front panel and remotely through a web interface. It is also possible to control or monitor the FRC0730 via RMCP or SNMP.
Key features
Agile IF to L-band Up & Down Converter
Optional up-conversion to C, Ku or DBS-band
Ultra fine frequency resolution
IF frequency switchable between 70 MHZ & 140 MHz
Very high frequency stability
Very low spurious characteristics
Phase noise compliant to Intelsat IBS/ Eutelsat SMS
High linearity over the entire bandwidth
Optional10 MHz + DC power for BUC
Optional LNB power supply + 10 MHz
';
CX-4
CX-4 Transport stream converter.
The CX-4 is a flexible 1U unit containing four independent transport stream converters, each of which can be user configured to convert between Transport Streams over IP to Asynchronous Serial Interface (TSoIP to ASI) or Asynchronous Serial Interface to Transport Streams over IP (ASI to IP). This flexibility ensures your capital costs to a minimum as you can be sure you always have the correct converter to hand.
Complying with both the DVB and SMPTE2022 standards the TSoIP interface supports Transport stream encapsulation, forward error correction and UDP/RTP de-encapsulation as defined by the SMPTE 2022 specification. Hence allowing you to match the resilience of your stream to the performance of your network.
This professional product is designed for easy and reliable operation. It is controlled via a GUI using the onboard web server which is on a separate IP interface to the TSoIP signals. The chassis is fitted with dual power supplies and adequate ventilation to ensure for reliable service in the broadcast environment.
For added flexibility the unit can be configure at manufacture with any combination of one to four converters.
Applications: For use in Terrestrial, Cable and Satellite broadcast systems.
';
New FRC0740 L-band Block Upconverter
The FRC0740 is easy to operate and monitor. All control and monitoring parameters are available locally on the front panel and remotely through a web interface. It is also possible to control or monitor the FRC0740 via RMCP or SNMP.
Key features
Wide choice of RF frequency ranges covering C, Ku and DBS-bands
Very high frequency stability
Very low spurious characteristics
2 L-band inputs and one L-band output
Integrated signal combiner
Very high linearity
Very good gain flatness over the entire bandwidth
';
New FRC0750 Active L-Band Combiner and Upconverter
A DC power supply and a reference frequency are also available on the L-band output, providing a compact and cost effective solution when the FRC0750 is used in combination with an outdoor RF upconverter and/or amplifier.
The FRC0750 can be delivered with an integrated block upconverter as option. In this configuration, the FRC0750 converts the L-band output signal of the combiner to C, Ku or DBS-band. The FRC0750 is easy to operate and monitor. All control and monitoring parameters are available locally on the front panel and remotely through a web interface. It is also possible to control or monitor the FRC0750 via Newtec’s proprietary RMCP protocol or via SNMP.
Key features
Up to 8 L-band inputs
Each input is switchable and gain adjustable
Optional upconversion to C, Ku or DBS-band
Optional 10 MHz +DC power for BUC
Optional 10 MHz reference input/output
Advanced monitoring and control
';
UHD Scaling Cross Converter
THEFINE's UHD Scaling Cross Converter
[Features of TFC-21Q3 & TFC-21CC]
';
BD30AV-UHD
';
